Delayed onset of photochromism in molybdenum oxide films caused by photoinduced defect formation.
نویسندگان
چکیده
We report the photochromic properties of amorphous MoO3 films deposited by dc sputtering with different O2 flow rates. The kinetics of film coloration under UV light irradiation is determined using optical transmission spectroscopy. Changes in the absorbance and refractive index were derived from the analysis of transmittance spectra. The absorbance spectra exhibited a growing broad peak centered around 830 nm, which was induced by the UV irradiation. In the early stages of irradiation, the absorbance of the films did not change but their refractive indices did change. This induction time was correlated with the O2 partial pressure during the film deposition, which was controlled by the O2 flow rate. The origins of this observation are discussed.
منابع مشابه
Thermal Oxidation Times Effect on Structural and Morphological Properties of Molybdenum Oxide Thin Films Grown on Quartz Substrates
Molybdenum oxide (α-MoO)thin films were prepared on quartz and silicon substrates by thermal oxidation of Mo thin films deposited using DC magnetron sputtering method. The influence of thermal oxidation times ranging from 60-240 min on the structural and morphological properties of the preparedfilms was investigated using X-ray diffraction, Atomic force microscopy and Fourier transform infrared...
متن کاملStructural, Electrical and Optical Properties of Molybdenum Oxide Thin Films Prepared by Post-annealing of Mo Thin Films
Molybdenum thin films with 50 and 150 nm thicknesses were deposited on silicon substrates, using DC magnetron sputtering system, then post-annealed at different temperatures (200, 325, 450, 575 and 700°C) with flow oxygen at 200 sccm (standard Cubic centimeter per minute). The crystallographic structure of the films was obtained by means of x-ray diffraction (XRD) analysis. An atomic force micr...
متن کاملStructural, Electrical and Optical Properties of Molybdenum Oxide Thin Films Prepared by Post-annealing of Mo Thin Films
Molybdenum thin films with 50 and 150 nm thicknesses were deposited on silicon substrates, using DC magnetron sputtering system, then post-annealed at different temperatures (200, 325, 450, 575 and 700°C) with flow oxygen at 200 sccm (standard Cubic centimeter per minute). The crystallographic structure of the films was obtained by means of x-ray diffraction (XRD) analysis. An atomic force micr...
متن کاملFormation of Molybdenum Oxide Nano-whiskers during Heating Compressed Powder
In this study the synthesis of molybdenum oxide nano-whiskers with circular cross-section is performed. In some areas, it was observed that also some whiskers have open tips exhibiting their hollow structures. These whiskers have side dimensions ranging 2-5 μm with an average diameter in the nanometer rang. The structure suggested the vapor-liquid-solid growth mechanism (VLS). Scanning elect...
متن کاملFormation of Cupric Oxide Films on Quartz Substrates by Annealing the Copper Films
In the present work, cupric oxide (CuO) films were obtained through thermal annealing of the copper (Cu) films deposited on quartz substrates by DC magnetron sputtering method. The annealing was performed in air atmosphere for different times ranging from 60-240 min at temperature of 400 ºC. The influence of annealing times on structural and morphological properties of the films was investi...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Science and technology of advanced materials
دوره 12 5 شماره
صفحات -
تاریخ انتشار 2011