The strain path dependence of plastic deformation response of AA5754: Experiment and modeling
نویسندگان
چکیده
This work presents modeling of experiments on a balanced biaxial (BB) pre-strained AA5754 alloy, subsequently reloaded uniaxially along the rolling direction and transverse direction. The material exhibits a complex plastic deformation response during the change in strain path due to 1) crystallographic texture, 2) aging (interactions between dislocations and Mg atoms) and 3) recovery (annihilation and re-arrangement of dislocations). With a BB prestrain of about 5 %, the aging process is dominant, and the yield strength for uniaxially deformed samples is observed to be higher than the flow stress during BB straining. The strain hardening rate after changing path is, however, lower than that for pre-straining. Higher degrees of pre-straining make the dynamic recovery more active. The dynamic recovery at higher strain levels compensates for the aging effect, and results in: 1) a reduction of the yield strength, and 2) an increase in the hardening rate of re-strained specimens along other directions. The yield strength of deformed samples is further reduced if these samples are left at room temperature to let static recovery occur. The synergistic influences of texture condition, aging and recovery processes on the material response make the modeling of strain path dependence of mechanical behavior of AA5754 challenging. In this study, the influence of crystallographic texture is taken into account by incorporating the latent hardening into a visco-plastic self-consistent model. Different strengths of dislocation glide interaction models in 24 slip systems are used to represent the latent hardening. Moreover, the aging and recovery effects are also included into the latent hardening model by considering strong interactions between dislocations and dissolved atom Mg and the microstructural evolution. These microstructural considerations provide a powerful capability to successfully describe the strain path dependence of plastic deformation behavior of AA5754.
منابع مشابه
Simulation of deformation behavior of porous Titanium using Modified Gurson yield function
In this research the stress-strain curve of porous Titanium, as a common material for biomedical application, was predicted using the mechanical properties of fully solid Titanium experimental data. Modified Gurson model (Gurson-Tvergaard-Needleman (GTN) model) was used to predict the plastic response of porous Titanium in compaction. Different values of GTN parameters were used for different i...
متن کاملThe Effect of Fe Additive on Plastic Deformation for Crush-Boxes with Closed-Cell Metal Foams, Part II: Al-Composite Foam-Filled brass tubes Compression Response
The brass tubes with foam cores of AlSi7SiC3, AlSi7SiC3Fe1 and AlSi7SiC3Fe3 were produced as the crush-boxes with circle and square cross-section. Then axial compressive behavior and energy absorption capability of the foam-filled tubes were investigated during the quasi-static progressive plastic buckling. The uniaxial compressive stress–strain curves of the foam-filled brass tubes exhibited t...
متن کاملEffect of Fe additive on plastic deformation for crush-boxes with closed-cell metal foams, Part I: Al-composite foam compression response
AbstractIn this paper, we investigate effect of Fe–intermetallic compounds on plastic deformation of closed-cell composite Aluminum Foam as filler of thin-walled tubes. However, deformation of the Aluminum foam-filled thin-walled tubes as crushed-box will be presented in Part (II). Composite foams of AlSi7SiC3 and AlSi7SiC3-(Fe) as closed cell were synthesized by powder metallurgy foaming metho...
متن کاملA Study of the Fundamental Relationships between Deformation-Induced Surface Roughness and Strain Localization in AA5754
Three-dimensional, matrix-based statistical analysis methods were developed and integrated with high-resolution topographical imaging, to assess how microstructural changes influence the evolution of plastic deformation and strain localization in a commercial AA5754-O aluminum sheet in three in-plane strain modes. Analysis of the raw surface data revealed that the general composition of the sur...
متن کاملOptimization of die geometry for Tube Channel Pressing
Since tubes have numerous industrial applications, different attempts are focused on the Severe Plastic Deformation (SPD) processes of tubes. As an illustration, Tube Channel Pressing (TCP) is an attractive process for this purpose since it can be used for processing of different sizes of tubes. However, more attempts are needed to improve the outcomes of TCP. For example, imposing of greater s...
متن کامل