Mathematical modeling supports the presence of neutrophil depriming in vivo
نویسندگان
چکیده
Abstract Following migration into the intestinal mucosa in inflammatory bowel disease (IBD), neutrophils enter the intestinal lumen and are excreted. This provides a basis for quantification of disease activity by measuring excreted label following injection of In-111-labeled neutrophils. In severe pan-colitis, 50% of the injected In-111 is typically recovered in the feces, indicating that 50% of neutrophil turnover is via fecal excretion. Neutrophils have an intravascular lifespan of ~10 h and a distribution volume of ~10 L, so total body neutrophil turnover is 10.N/10 cells/h, where N is the peripheral blood neutrophil count (cells/L). Neutrophil loss via the colon in a patient with 50% fecal In-111 loss is therefore N/120 cells/min. Pan-colonic mucosal-blood flow in pan-colitis is 200 mL/min, which would deliver N/5 neutrophils to the colon per min. Therefore, 5/120, or 4%, of incoming neutrophils undergo migration into inflamed bowel. If the 96% of nonmigrating cells exit in a primed state, then at steady state >90% of circulating neutrophils would be primed if no depriming took place. As the highest level of priming seen in IBD is ~40%, this indicates that depriming within the circulation must take place. Using the above values in the steady state equation relating priming rate to depriming rate plus primed-cell destruction rate gives a mean depriming time of 35 min. We conclude that a very small proportion of neutrophils entering a site of inflammation migrate and that in vivo depriming must take place to limit the numbers of primed neutrophils in the circulation.
منابع مشابه
Mechanical deformation induces depolarization of neutrophils
The transition of neutrophils from a resting state to a primed state is an essential requirement for their function as competent immune cells. This transition can be caused not only by chemical signals but also by mechanical perturbation. After cessation of either, these cells gradually revert to a quiescent state over 40 to 120 min. We use two biophysical tools, an optical stretcher and a nove...
متن کاملDiscrimination of Human Cell Lines by Infrared Spectroscopy and Mathematical Modeling
Variations in biochemical features are extensive among cells. Identification of marker that is specific for each cell is essential for following the differentiation of stem cell and metastatic growing. Fourier transform infrared spectroscopy (FTIR) as a biochemical analysis more focused on diagnosis of cancerous cells. In this study, commercially obtained cell lines such as Human ovarian carcin...
متن کاملMathematical Modeling of Carbon Dioxide Removal from the CO2/CH4 Gas Mixture Using Amines and Blend of Amines in Polypropylene: A Comparison between Hollow Fiber Membrane Contactor and Other Membranes
In this work, a mathematical model is established to describe the removal of CO2 from gaseous mixtures including CH4 and CO2 in a polypropylene hollow fiber membrane contactor in the presence of conventional absorbents such as monoethanolamine (MEA), methyldiethanolamine (MDEA), and a blend of them. Modeling was performed in axial and radial directions under the fully-wet condition for counterc...
متن کاملImprovement of Methanol Synthesis Process through a Novel Sorption-Enhanced Fluidized-bed Reactor, Part I: Mathematical Modeling
In the first part of two section paper, a mathematical model of the fluidized bed reactor in the presence of in-situ water adsorbent for methanol synthesis is assessed. The bubbling two-phase regime is applied to model the fluidization concept. The binary adsorbent and catalyst particles system can be separated from each other based on their density difference. The heavy catalyst particles tend...
متن کاملNonlinear Dynamic Modeling and Hysteresis Analysis of Aerospace Hydro - dynamical Control Valves
A new procedure for deriving nonlinear mathematical modeling for a specific class of aerospace hydro - mechanical control valves is presented. The effects of friction on the dynamic behavior of these types of valves along with the experimental verifictions are also given. The modeling approach is based on the combination of the following three tasks: decomposition of the valve into simple speci...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
دوره 2 شماره
صفحات -
تاریخ انتشار 2014