Effect of resin thickness, and curing time on the micro-hardness of bulk-fill resin composites
نویسندگان
چکیده
BACKGROUND Bulk-fill resin composite has been introduced, their manufacturers claimed that they can be applied in bulks of 4mm, without necessitating a prolonged curing time, or a light curing unit with increased irradiance. Thus this study was conducted to evaluate the effect of resin thickness, and curing time on the micro-hardness of two bulk -fill resin composites; Tetric Evo-Ceram [TE], and X-trafil [XF]. MATERIAL AND METHODS 120 cylindrical specimens were prepared, and divided into 24 groups (n=5/group), representing the two bulk-fill resin composites, three different material thicknesses (2, 3 and 4 mm) and the four curing times used in the study (10, 20, 40, and 60 seconds). The specimens were light-cured from the top surface only. Specimens were stored in light proof containers in complete darkness at 37°C for 24 hours. Micro-hardness test was conducted on both top and bottom surfaces using Vickers micro-hardness tester with 500 g load and a dwell time of 15 seconds. Data were statistically analyzed by Four-way ANOVA of Variance. The significance level was set at P ≤ 0.05. Pearson Correlation used to determine significant correlations between mean micro-hardness (top) and (bottom) surfaces. RESULTS Four way-ANOVA shows that different tested materials produce a statistically significant effect on mean micro-hardness (VHN) at p≤0.001, while thickness, curing time, and surface revealed statistically non significant effect on mean micro-hardness (VHN) at p≥0.05. [XF] (92.01±3.15 VHN) showed statistically significant higher mean micro-hardness than [TE] (54.13±4.96 VHN). Pearson Correlation revealed that there was a significant direct correlation between micro-hardness (bottom) and mean micro-hardness (top) (mm), r = 0.985, p (2-tailed) ≤0.001. CONCLUSIONS Within the limitations of this study, the bulk-fill resin composites used in this study can be placed and cured properly in the 4 mm bulk. KEY WORDS Bulk-fill resin composite, micro-hardness, thickness, curing time.
منابع مشابه
The effect of different insertion techniques on the depth of cure and vickers surface micro-hardness of two bulk-fill resin composite materials
BACKGROUND The aim of this study was to evaluate the Vickers surface micro-hardness and the depth of cure of two bulk-fill resin composites and one incremental-fill resin composite. MATERIAL AND METHODS Two Bulk-fill dental resin composites (X-tra Fil, Voco; Sonic-FillTM 2, Kerr Corporation) and an incremental-fill dental resin composite (Filtek™ Z250 XT, 3M ESPE) were used. Sixty cylindrical...
متن کاملEffect of resin thickness on the microhardness and optical properties of bulk-fill resin composites
OBJECTIVES This study evaluated the effects of the resin thickness on the microhardness and optical properties of bulk-fill resin composites. METHODS Four bulk-fill (Venus Bulk Fill, Heraeus Kulzer; SDR, Dentsply Caulk; Tetric N-Ceram Bulk Fill, Ivoclar vivadent; SonicFill, Kerr) and two regular resin composites (Charisma flow, Heraeus Kulzer; Tetric N-Ceram, Ivoclar vivadent) were used. Sixt...
متن کاملEffect of modulated photo-activation on polymerization shrinkage behavior of dental restorative resin composites.
This study investigated the influence of modulated photo-activation on axial polymerization shrinkage, shrinkage force, and hardening of light- and dual-curing resin-based composites. Three light-curing resin composites (SDR bulk-fill, Esthet X flow, and Esthet X HD) and one dual-curing material (Rebilda DC) were subjected to different irradiation protocols with identical energy density (27 J c...
متن کاملThe effects of Exposure Times and Light Curing Sources on Surface Micro-Hardness of a Resin Modified Glass Ionomer
Introduction: The aim of this study was to evaluate the influenceof different light curing systems and curing times on the micro-hardness of aresin modified glass ionomer. Methods: Forty two samples of ResinModified Glass Ionomer (RMGI) were prepared using stainless steel cylindrical mold(8 × 2 mm) and randomly divided into six groups of seven. Three groups werecured with a Quartz Tungsten Halo...
متن کاملThe Effect of Bulk Depth and Irradiation Time on the Surface Hardness and Degree of Cure of Bulk-Fill Composites
STATEMENT OF PROBLEM For many years, application of the composite restoration with a thickness less than 2 mm for achieving the minimum polymerization contraction and stress has been accepted as a principle. But through the recent development in dental material a group of resin based composites (RBCs) called Bulk Fill is introduced whose producers claim the possibility of achieving a good resto...
متن کامل