Numerical Modelling of Mechanical Behavior of Coal Mining Hard Roofs in Different Backfill Ratios: A Case Study

نویسندگان

  • Meng Li
  • Nan Zhou
  • Zhicheng Liu
چکیده

In coal mining hard roofs are one of the main factors causing the occurrence of rock bursts in working panels. To solve this problem, the solid backfill coal mining (SBCM) technique is proposed and used as an effective measure to prevent the rock bursts induced by hard roofs. However, due to the different backfill ratios of working planes, the control effects on hard roofs are quite unique. By using a numerical simulation, this study simulates the deformation of hard roofs and distributions of stress and strain energies in different roof-control backfill ratios, so as to reveal the control mechanisms of SBCM on hard roofs. The results show that, when the roof-controlled backfill ratio are 0, 40% and 60%, the ratio exerts no influence on the distributions of advanced abutment stress and strain energies. While for roof-control backfill ratios of 82.5%, 91% and 93%, the advanced abutment stress and strain energies decrease significantly, but the increment of the ratio exerts little influence on the decrease. When the roof-control backfill ratio reaches 97%, the advanced abutment stress and strain energies again decrease. In this context, the stress concentration factor is only 1.5 and the peak strain energy is 544 kJ/m3, the stress concentration factor and peak strain energy decrease by 45.7% and 63.9%, respectively, compared with the caving method. As the roof-controlled backfill ratio rises, backfill materials tend to support hard roofs, thus significantly preventing dynamic hazards.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Deformation Behavior of Hard Roofs in Solid Backfill Coal Mining Using Physical Models

Solid backfill coal mining technology has been widely applied in coal seams that are at risk of hard roof. Using actual measured strain–stress curves of the backfill body and the similarity theory, this study designed and employed four experimental models for physical simulation, corresponding to roof-controlled backfilling ratios of 0%, 40%, 82.5% and 97% using the geological conditions of Fac...

متن کامل

Analysis and Prevention of Geo-Environmental Hazards with High-Intensive Coal Mining: A Case Study in China’s Western Eco-Environment Frangible Area

This study seeks to address the problems of major geo-environmental hazards caused by high-intensive coal mining in China’s western eco-environment frangible area including strong mining pressure, surface subsidence, soil and water loss, and land desertification. Using the high-intensive mining at the Xiao-jihan Coal Mine, this paper investigates the compaction characteristics of aeolian sand-b...

متن کامل

Numerical modelling of the underground roadways in coal mines– uncertainties caused by use of empirical-based downgrading methods and in situ stresses

Numerical modelling techniques are not new for mining industry and civil engineering projects anymore. These techniques have been widely used for rock engineering problems such as stability analysis and support design of roadways and tunnels, caving and subsidence prediction, and stability analysis of rock slopes. Despite the significant advancement in the computational mechanics and availabili...

متن کامل

Analysis on Filling Ratio and Shield Supporting Pressure for Overburden Movement Control in Coal Mining with Compacted Backfilling

Since the weight of overburden is sustained by both the backfill body and the unmined solid coal in coal mining with compacted backfilling (CMCB) panels, the stress and deformation characteristics of the surrounding rocks in coal mining are radically changed. The overburden movement control mechanism by coordinating with backfill body and shield in CMCB was studied systematically in this paper....

متن کامل

Numerical Modelling of Backfill Grouting Approaches in EPB Tunneling

One of the main issues involved during tunnel construction with tunnel boring machines is the tail gap grouting. This gap is between the external diameter of tunnel lining and the excavation boundary that is filled with high-pressure grouting materials. In this work, three different approaches of gap grouting modeling in the FLAC3D software are investigated with a special attention to the...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017