High Temperature Materials and Mechanisms

نویسنده

  • Y. Bar-Cohen
چکیده

Given the wide topic coverage and the sometimes introductory character of the book, it is not helpful that only 21 bibliographic entries are provided for the entire book. The offer of a wider bibliography selection would significantly improve the usefulness of the book, since its topic diversity is likely to require for most readers additional reading on some of the topics. Dr M. Sergio Campobasso Senior Lecturer in Mechanical Engineering – Renewable Energy Systems Department of Engineering Lancaster University

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The Effect of Deformation Temperature on the Mechanical Properties and Microstructural Evolutions of High Manganese TWIP Steel

In this study, the effect of tensile test temperature (148 to 673 K) on the microstructural evolutions and the mechanical properties of high manganese twinning induced plasticity (TWIP) steel with the chemical composition of Fe- 31Mn-3Al-3Si (wt. %) was investigated. XRD, SEM and TEM were used to study the microstructural evolutions. Stacking fault energy (SFE) of the alloy was also calculated ...

متن کامل

Kinetic Modeling of the High Temperature Water Gas Shift Reaction on a Novel Fe-Cr Nanocatalyst by Using Various Kinetic Mechanisms

In this work the kinetic data demanded for kinetic modeling were obtained in temperatures 350, 400, 450 and 500 oC by conducting experimentations on a Fe-Cr nanocatalyst prepared from a novel method and a commercial Fe-Cr-Cu one. The collected data were subjected to kinetic modeling by using two models derived from redox and associative mechanisms as well as an empirical one. The coefficients o...

متن کامل

HOT CRACK FORMATION IN PURE CU AND CU-30%ZN ALLOY DURING IN SITU SOLIDIFICATION

The hot cracking susceptibility can be determined by establishing the transition temperature between brittle and ductile fracture at high temperature tensile testing of in situ solidified samples. High temperature tensile properties were determined for commercial cathodic pure Cu and Cu- 30%Zn alloy. The transition temperatures for pure Cu and Cu-30%Zn were evaluated from ultimate tensile stres...

متن کامل

On the Use of Accelerated Aging Methods for Screening High Temperature Polymeric Composite Materials

A rational approach to the problem of accelerated testing of high temperature polymeric composites is discussed. The methods provided are considered tools useful in the screening of new materials systems for long-term application to extreme environments that include elevated temperature, moisture, oxygen, and mechanical load. The need for reproducible mechanisms, indicator properties, and real-...

متن کامل

Preparation and Investigation of Poly (N-isopropylacrylamide-acrylamide) Membranes in Temperature Responsive Drug Delivery

Objective(s) Physiological changes in the body may be utilized as potential triggers for controlled drug delivery. Based on these mechanisms, stimulus-responsive drug delivery has been developed. Materials and Methods In this study, a kind of poly (N-isopropylacrylamide-acrylamide) membrane was prepared by radical copolymerization. Changes in swelling ratios and diameters of the membrane wer...

متن کامل

FAILURE MECHANISMS OF REFRACTORY LININGS FOR NONFERROUS FLASH SMELTING FURNACES

Although the flash smelting technologies use different furnace designs, the refractory linings are exposed to very similar aggressive environments and, as a result, the corrosion analysis results on one type of furnace could be generally applied to other furnaces of similar high temperature processes. Particularities regarding the different chemistries of the pyrometallurgical process and opera...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2014