Influence of the type of post and core on in vitro marginal continuity, fracture resistance, and fracture mode of lithia disilicate-based all-ceramic crowns.

نویسندگان

  • Nicole Forberger
  • Till N Göhring
چکیده

STATEMENT OF PROBLEM The influence of different crown foundations on marginal seal and fracture resistance of ceramic crowns placed on endodontically treated teeth has not been clearly established. PURPOSE The purpose of this study was to evaluate the marginal continuity and fracture behavior of high-strength all-ceramic crowns with different substructures in endodontically treated premolars. MATERIAL AND METHODS Forty-eight human mandibular premolars were assigned to 6 groups, including a no-treatment group (UNTREATED) and a group for which the access cavity was restored with composite resin (Tetric Ceram) (COMP). In the remaining 4 groups, teeth were prepared to receive all-ceramic crowns with 0.8-mm-wide shoulders and axial dentin heights of 2 mm. No posts were used in the ENDOCROWN group. Glass fiber posts (FRC Postec) were used in group FRC-POST. Group ZRO-POST received zirconia ceramic posts (CosmoPost), and group GOLD-POST received cast gold posts (CM). Experimental lithia disilicate ceramic crowns were made and adhesively cemented (Variolink). All teeth were subjected to thermal cycling and mechanical loading (TCML) in a masticatory simulator (1,200,000 loads, 49 N, 1.7 Hz, 3000 temperature cycles of 5 degrees C-50 degrees C-5 degrees C). Marginal continuity was evaluated with scanning electron microscopy at x200. All specimens were loaded to failure in a universal testing machine at 0.5 mm/min after TCML. Data were analyzed using 1-way ANOVA and post hoc t tests with Bonferroni correction (alpha=.05). RESULTS Initially, mean values (SD) between 72.4 (15.8)% (ENDOCROWN) and 94.8 (3)% (FRC-POST) for continuous margins were found. With TCML, marginal continuity decreased significantly only in FRC-POST, to 75.5 (8.4)%, and in ENDOCROWN, to 44.7 (14.5)%. Mechanical load testing measured mean loads to failure between 1092.4 (307.8) N (FRC-POST) and 1253.7 (226.5) N (ZRO-POST) without significant differences between groups. Deep root fractures were observed in half of the specimens, irrespective of their groups. CONCLUSIONS Marginal continuity of the crowns studied was better and more stress resistant when posts and cores were included in the restoration of endodontically treated teeth with complete ceramic crowns. The placement of a post-and-core foundation did not influence the pattern of failure.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The Effect of Different Marginal Designs on the Fracture Resistance of Monolithic Zirconia Crowns

Abstract   Background and Aim: One of the major problems of all ceramic restorations is their probable fracture against the occlusal force. The aim of the present in vitro study is to compare the effect of three marginal designs (shoulder, sloped shoulder, chamfer) on the fracture resistance of monolithic zirconia crowns. Materials and methods: In this in vitro study, three PEEK dies with cham...

متن کامل

Effect of marginal design on fracture resistance of IPS e.maxall ceramic restorations: Chamfer versus shoulder finish lines

Background and Aim: One of the problems of all ceramic restorations is their risk of fracture due to occlusal loads. The aim of the present study was to compare the effect of two marginal designs (shoulder and chamfer) on the fracture resistance of IPS-emax all ceramic restorations. Materials and Methods: One extracted maxillary first premolar received chamfer 50' marginal preparation (0.8 m...

متن کامل

Fracture resistance of aluminium oxide and lithium disilicate-based crowns using different luting cements: an in vitro study.

AIM The aim of this study was to investigate the fracture resistance of two types of ceramic crowns cemented with two different cements. METHODS AND MATERIALS Forty premolar crowns were fabricated using lithium-disilicate (IPS Empress-2) and glass-infiltrated aluminium-oxide (In-Ceram) ceramic systems. The crowns were divided into four groups (n=10) with Group 1 (IPS Empress-2) and Group 2 (I...

متن کامل

Fracture resistance of implant- supported monolithic crowns cemented to zirconia hybrid-abutments: zirconia-based crowns vs. lithium disilicate crowns

PURPOSE The aim of this in vitro study was to investigate the fracture resistance under chewing simulation of implant-supported posterior restorations (crowns cemented to hybrid-abutments) made of different all-ceramic materials. MATERIALS AND METHODS Monolithic zirconia (MZr) and monolithic lithium disilicate (MLD) crowns for mandibular first molar were fabricated using computer-aided design...

متن کامل

Comparison of the effect of shoulder and contra bevel preparation on fracture resistance of teeth restored with cast posts

Comparison of the effect of shoulder and contra bevel preparation on fracture resistance of teeth restored with cast posts Dr. SA. Shayegh* - Dr. F. Gangy** *- Assistant Professor of Prosthodontics Dept. - Faculty of Dentistry – Shahed University of Medical Sciences. **- Dentist. Background and Aim: Studies concerning the effects of post-core design on fracture resistance of endodontically trea...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • The Journal of prosthetic dentistry

دوره 100 4  شماره 

صفحات  -

تاریخ انتشار 2008