Low-Loss Matching Network Design for Band-Switchable Multi-Band Power Amplifier
نویسندگان
چکیده
This paper presents a novel design scheme for a bandswitchable multi-band power amplifier (BS-MPA). A key point of the design scheme is configuring multi-section reconfigurable matching networks (MR-MNs) optimally in terms of low loss matching in multiple frequency bands from 0.7 to 2.5 GHz. The MR-MN consists of several matching sections, each of which has a matching block connected to a transmission line via a switch. Power dissipation at an actual on-state switch results in the insertion loss of the MR-MN and depends on how the impedance is transformed by the MR-MN. The proposed design scheme appropriately transforms the impedance of a high power transistor to configure a low loss MR-MN. Numerical analyses show quantitative improvement in the loss using the proposed scheme. A 9-band 3-stage BS-MPA is newly designed following the proposed scheme and fabricated on a multi-layer low temperature co-fired ceramic substrate for compactness. The BS-MPA achieves a gain of over 30 dB, an output power of greater than 33 dBm and a power added efficiency of over 40% at the supply voltage of 4 V in each operating band. key words: power amplifier, reconfigurable, matching network, multiband, switch
منابع مشابه
A Broadband Low Power CMOS LNA for 3.1–10.6 GHz UWB Receivers
A new approach for designing an ultra wideband (UWB) CMOS low noise amplifier (LNA) is presented. The aim of this design is to achieve a low noise figure, reasonable power gain and low power consumption in 3.1-10.6 GHz. Also, the figure of merit (FOM) is significantly improved at 180nm technology compared to the other state-of-the-art designs. Improved π-network and T-network are used to obt...
متن کاملA W-band Simultaneously Matched Power and Noise Low Noise Amplifier Using CMOS 0.13µm
A complete procedure for the design of W-band low noise amplifier in MMIC technology is presented. The design is based on a simultaneously power and noise matched technique. For implementing the method, scalable bilateral transistor model parameters should be first extracted. The model is also used for transmission line utilized in the amplifier circuit. In the presented method, input/output ma...
متن کاملDesign of an S-band Ultra-low-noise Amplifier with Frequency Band Switching Capability
In this paper, an ultra-low-noise amplifier with frequency band switching capability is designed, simulated and fabricated. The two frequency ranges of this amplifier consist of the 2.4 to 2.5 GHz and 3.1 GHz to 3.15 GHz frequency bands. The designed amplifier has a noise figure of less than 1dB, a minimum gain of 23 dB and a VSWR of less than 2 in the whole frequency band. The design process s...
متن کاملA Concurrent Dual-Band Low Noise Amplifier for GNSS Receivers
In this paper, a new design of concurrent dual-band Low Noise Amplifier (LNA) for multi-band single-channel Global Navigation Satellite System (GNSS) receivers is proposed. This new structure is able to operate concurrently at frequency of 1.2 and 1.57 GHz. Parallel and series resonance parts are employed in the input matching in order to achieve concurrent performance. With respect to used pse...
متن کاملA 28-36 GHz Optimized CMOS Distributed Doherty Power Amplifier with A New Wideband Power Divider Structure
Background and Objectives: In this paper, a new design strategy was proposed in order to enhance bandwidth and efficiency of power amplifier. Methods: To realize the introduced design strategy, a power amplifier was designed using TSMC CMOS 0.18um technology for operating in the Ka band, i.e. the frequency range of 26.5-40GHz. To design the power amplifier, first a power divider (PD) with a ver...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- IEICE Transactions
دوره 95-C شماره
صفحات -
تاریخ انتشار 2012