Uncertainty quantification for engineering design

and keywords page. This is page 2 and should include (a) the article’s full title, (b) an abstract of no more than 300 words, and (c) up to 5 keywords or phrases that reflect the content and major thrust of the article. The abstract should give a succinct account of the objective, methods, results, and significance of the subject matter. Introduction. This section begins on page 3 and should clearly state the objective of the research in the context of previous work bearing directly on the subject. An extensive review of the literature is usually not appropriate. Notations in text. Customary abbreviations will be accepted and the authors are recommended to employ Système Internationale (SI/metric) units. Special and unusual symbols should be clearly presented and in a common font. Spell out acronyms at first use, and use only acronyms thereafter. All equipment supplies and products stated in the article should have the manufacturer name and location identified at first mention. Tables. Tables should be numbered consecutively with Arabic numerals, and each should be double-spaced on separate pages after the references. A short explanatory title and column headings should make the table intelligible and a footnote should define all terms without reference to the text. All tables must be cited sequentially and their approximate positions indicated in the text. Figures and captions. The number of figures should be the minimum necessary to make the essential points of the paper. Figures should be no larger than 6 8 in. (approx. 200 250 mm) and should be included in a separate file. Figures should be composed to occupy one column (20 picas or 8.3 cm) or two columns (41.5 picas or 17 cm) after reduction. Diagrams and illustrations must have a professional appearance and be created with high-resolution lettering to permit reduction. To assure legibility, letters, numbers, and symbols on figures should all be the same size and have a minimum height of 2 mm (i.e., 6 points on the pica scale) when reduced. Figures should be separate and not incorporated into the text copy. Each figure must be cited sequentially and its approximate position clearly indicated within the text. Figures must be numbered consecutively with Arabic numerals and be accompanied by a descriptive double-spaced caption provided at the end of the article. The captions should concisely describe the figure, identify any symbols and/or calibration bars, and define any terms or acronyms. Acceptable figure file formats are MS Word, EPS, JPEG, TIFF, PS, and PDF. Artwork should normally be in black and white; if authors have color figures, the publisher will provide a price quotation for the additional production costs. However, color figures can appear online free of charge. All figures must be printed separately and identified with the short title of the paper, figure number, and figure orientation (top or bottom). Three complete sets of figures should be carefully packaged in protective envelopes, one to accompany each copy of the manuscript. References. The alphabetical list of references begins a new page after the text. Each in-text citation must have a corresponding reference and vice versa. Only conference papers, theses, and published or in press articles and books should appear in this list. All authors’ names should be included, followed by the year of publication. For journals, the full title of the journal, volume, issue number, and inclusive page numbers should be provided. For books, the full title should be given, followed by the editors, volume number (if any), page numbers, place of publication, and publisher. Citations in the text should read Brown and Goel (2010) or (Brown & Goel, 2010). Where there are more than two authors the citation should read Brown et al. (2010). When more than one paper by the same authors has appeared in the same year, they are distinguished by (Brown & Goel, 2010a, 2010b). Multiple citations in the text should be in chronological order (Dym, 1994; Birmingham, 1999; Brown, 2010). Journal or Magazine Article Brown, D.C. (2010). AI EDAM at the cutting edge. Artificial Intelligence for Engineering Design, Analysis and Manu facturing 24(3), 281–282. Frey, D., Birmingham, W., & Dym, C. (2010). Design pedagogy: representations and processes [Guest editorial]. Artificial Intelligence for Engineering Design, Analysis and Manufacturing 24(3), 283–284. Knight, T., & Sass, L. (2010). Looks count: computing and constructing visually expressive mass customized housing. Artificial Intelligence for Engineering Design, Analysis and Manufacturing 24(3), 425–445. Book Dym, C.L. (1994). Engineering Design: A Synthesis of Views. New York: Cambridge University Press. Chapter in Edited Book Goodman, J., Clarke, S., Langdon, P., & Clarkson, P.J. (2007). Designers’ perceptions of methods of involving and understanding users. In Universal Access in Human Computer Interaction (Stephanidis, C., Ed.), LNCS Vol. 4554, pp. 126–136. New York: Springer. Proceedings With Publisher Identified Strickfaden, M., & Heylighen, A. (2007). Exploring the cultural capital of design educators. Proc. Int. Conf. Eng ineer ing Design, ICED’07. Paris: The Design Society. Proceedings With No Publisher Identified Shu, L., Hansen, H., Gegeckaite, A., Moon, J., & Chan, C. (2006). Case study in biomimetic design: handling and assembly of microparts. Proc. ASME 2006 Int. Design En gineering Technical Conf. & Computers and Information in En gineering Conf., Paper No. DETC2006/DTM-99398, Phil adelphia, PA, September 10–13. Author biographies. Brief author biographies must be provided at the end of each paper; they should not exceed 100 words for each author. COPYEDITING AND PAGE PROOFS The publisher reserves the right to copyedit manuscripts to conform to the style of AIEDAM. The corresponding author will receive page proofs for final proofreading. No rewriting of the final accepted manuscript is permitted at the proof stage, and authors may be charged for substantial changes.