Steam turbine model
نویسندگان
چکیده
In order to characterize the transient dynamics of steam turbines subsections, in this paper, nonlinear mathematical models are first developed based on the energy balance, thermodynamic principles and semi-empirical equations. Then, the related parameters of developed models are either determined by empirical relations or they are adjusted by applying genetic algorithms (GA) based on experimental data obtained from a complete set of field experiments. In the intermediate and low-pressure turbines where, in the sub-cooled regions, steam variables deviate from prefect gas behavior, the thermodynamic characteristics are highly dependent on pressure and temperature of each region. Thus, nonlinear functions are developed to evaluate specific enthalpy and specific entropy at these stages of turbines. The parameters of proposed functions are individually adjusted for the operational range of each subsection by using genetic algorithms. Comparison between the responses of the overall turbine-generator model and the response of real plant indicates the accuracy and performance of the proposed models over wide range of operations. The simulation results show the validation of the developed model in term of more accurate and less deviation between the responses of the models and real system where errors of the proposed functions are less than 0.1% and the modeling error is less than 0.3%. 2008 Elsevier B.V. All rights reserved.
منابع مشابه
Study of the Effects of Lacing Rods Location on Natural Frequencies in Last Stage Blades of a Steam Turbine
In this study, effects of lacing rods location on natural frequencies of last stage of a Steam Turbine Blades (STBs) have been investigated. STBs are critical and important elements in a turbine as well as power plants. One of the most important parameters in turbine blades is lacing rods location. In this paper, first, a three dimensional (3D) scan was used to produce the geometrical model of ...
متن کاملLyapunov Rule Based Model Reference Adaptive Controller Designs for Steam Turbine Speed
A steam turbine, heart of all refineries. This work presents the mathematical modelling of the steam turbine unit in isolated operating condition, based on the continuity equation including servomotor for actuation purpose. Steam turbine should run at a constant speed for its safe operation and frequency stability. Adaptation of different controller like Feedback, PI, PID using certain adaptati...
متن کاملThermodynamic Performance Assessment of Steam-Injection Gas-Turbine Systems
The cycles of the steam-injection gas-turbine systems are studied. The analyses of the parametric effects and the optimal operating conditions for the steam-injection gas-turbine (STIG) system and the regenerative steam-injection gas-turbine (RSTIG) system are investigated to ensure the maximum performance. Using the analytic model, the performance parameters of the system such as thermal effic...
متن کاملArtificial neural networking and fuzzy logic exergy controlling model of combined heat and power system in thermal power plant
This paper presents entropy generation minimisation model of combined heat and power system. The turbine control valves and heater throttle valves were analysed. The high-pressure control valves regulate the mass flow rate of steam into the turbine, whereas the intermediate-pressure and lowpressure control valves the steam pressure of the turbine extracts 3 and 5. The steam of the turbine extra...
متن کاملPerformance Analysis of CCGT Power Plant using MATLAB/Simulink Based Simulation
Combined Cycle Gas Turbine (CCGT) integrates two cyclesBrayton cycle (Gas Turbine) and Rankine cycle (Steam Turbine) with the objective of increasing overall plant efficiency. In modern gas turbine the temperature of the exhaust gases is in the range of 500 oC to 550 oC. Modern steam power plants have steam temperature in the range of 500 oC to 630 oC. Hence gas turbine exhaust can be utilized ...
متن کاملSilicone-polyether Copolymers as New Steam Turbine Oil Demulsifiers
Turbine oil plays an important role in supporting optimal steam turbine performance. Some additives in turbine oil can cause emulsification when the oil is contaminated by water, so demulsibility is a very important property of the steam turbine oil. In order to improve the demulsibility of steam turbine oil, two kinds of polyether-silicone comb copolymers are synthesized and used as steam turb...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Simulation Modelling Practice and Theory
دوره 16 شماره
صفحات -
تاریخ انتشار 2008