Endochondral growth in growth plates of three species at two anatomical locations modulated by mechanical compression and tension.
نویسندگان
چکیده
Sustained mechanical loading alters longitudinal growth of bones, and this growth sensitivity to load has been implicated in progression of skeletal deformities during growth. The objective of this study was to quantify the relationship between altered growth and different magnitudes of sustained altered stress in a diverse set of nonhuman growth plates. The sensitivity of endochondral growth to differing magnitudes of sustained compression or distraction stress was measured in growth plates of three species of immature animals (rats, rabbits, calves) at two anatomical locations (caudal vertebra and proximal tibia) with two different ages of rats and rabbits. An external loading apparatus was applied for 8 days, and growth was measured as the distance between fluorescent markers administered 24 and 48 h prior to euthanasia. An apparently linear relationship between stress and percentage growth modulation (percent difference between loaded and control growth plates) was found, with distraction accelerating growth and compression slowing growth. The growth-rate sensitivity to stress was between 9.2 and 23.9% per 0.1 MPa for different growth plates and averaged 17.1% per 0.1 MPa. The growth-rate sensitivity to stress differed between vertebrae and the proximal tibia (15 and 18.6% per 0.1 MPa, respectively). The range of control growth rates of different growth plates was large (30 microns/day for rat vertebrae to 366 microns/day for rabbit proximal tibia). The relatively small differences in growth-rate sensitivity to stress for a diverse set of growth plates suggest that these results might be generalized to other growth plates, including human. These data may be applicable to planning the management of progressive deformities in patients having residual growth.
منابع مشابه
Mechanical effects on skeletal growth.
The growth (i.e. increase of external dimensions) of long bones and vertebrae occurs longitudinally by endochondral ossification at the growth plates, and radially by apposition of bone at the periosteum. It is thought that mechanical loading influences the rate of longitudinal growth. The 'Hueter-Volkmann Law' proposes that growth is retarded by increased mechanical compression, and accelerate...
متن کاملModulation of vertebral and tibial growth by compression loading: diurnal versus full-time loading.
PURPOSE This study was designed to determine whether the amount of endochondral growth response to mechanical compression and the underlying growth mechanism differed with night-time or day-time loading, relative to full-time loading. METHODS Mechanical compression (nominally 0.1 MPa stress) was applied across tibial and tail vertebral growth plates of growing Sprague-Dawley rats. Four groups...
متن کاملAnatomical parameters of cardiopulmonary system, venous blood pCO2and pO2tensions and the development of ascites syndrome in two genetic line chickens that are differing in their growth rate
The present study was designed to examine the anatomical parameters of the cardiopulmonary system, the function of venous blood gas parameters and the development of ascites incidence in two genetic line chickens. Three hundred forty day-old chickens from two pure broiler breeder lines, which were different in their growth rate and susceptibility to ascites syndrome were obtained. The relative ...
متن کاملBuckling Behavior of Composite Plates with a Pre-central Circular Delamination Defect under in-Plane Uniaxial Compression
Delamination is one of the most common failure modes in composite structures. In the case of in-plane compressional loading, delamination of a layered flat structure can cause a local buckling in delaminated area which subsequently affects the overall stiffness of the initial structure. This leads to an early failure of the overall structure. Moreover, with an increase in load, the delaminated ...
متن کاملNUMERICAL ANALYSIS OF THE INFLUENCE OF STOPPING HOLES IN THE CRACK GROWTH
The fracture and crack growth of mechanical structures is a usual phenomenon which is due to the application of tensile, cyclic loading or thermal stresses on the structure. So introducing of methods to prevent the crack growth is useful. Afterward, one of the repairing methods of crack growth, consisting to make a hole in the crack tip to elimi-nate the sharp corners, was explained. This metho...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of orthopaedic research : official publication of the Orthopaedic Research Society
دوره 24 6 شماره
صفحات -
تاریخ انتشار 2006