Can Prevention of a Reherniation Be Investigated? Establishment of a Herniation Model and Experiments With an Anular Closure Device

نویسندگان

  • Hans-Joachim Wilke
  • Lena Ressel
  • Frank Heuer
  • Nicolas Graf
  • Stefan Rath
چکیده

STUDY DESIGN Biomechanical in vitro study. OBJECTIVE To establish a reliable in vitro herniation model with human cadaver spines that enables evaluation of anular closure devices. SUMMARY OF BACKGROUND DATA Biomechanically, it is desirable to close anulus defects after disc herniation to preserve as much nucleus as possible. Multiple anular closure options exist to prevent reherniation. A reliable test procedure is needed to evaluate the efficacy and reliability of these implants. METHODS Two groups of human lumbar segments (n = 6 per group) were tested under cyclic loading until herniation occurred or 100,000 load cycles were applied. One group contained moderate/severe degenerated discs. A second group had mild degenerated discs. Intradiscal pressure was measured in the intact state to confirm disc quality.If herniation occurred, the extruded material was reinserted into the disc and the anulus defect was treated with the Barricaid anular closure device (Intrinsic Therapeutics, Inc., Woburn, MA). Disc height and 3-dimensional flexibility of the specimens in the intact, defect, and implanted states were measured under pure moments in each principal motion plane. Afterwards, provocation of reherniation was attempted with additional 100,000 load cycles. RESULTS Likelihood of herniation was strongly linked to disc degeneration and supported by the magnitude of intradiscal pressure. In moderate/severe degenerated discs, only 1 herniation was created. In mild degenerated discs, herniations were reliably created in all specimens. Using this worst-case model, herniation caused a significant reduction of disc height, which was nearly restored with the implant. In no case was reherniation or implant migration visible after 100,000 load cycles after Barricaid implantation. CONCLUSION We established a human herniation model that reliably produced nucleus extrusion during cyclic loading by selecting specimens with low disc degeneration. The Barricaid seems to prevent nucleus from reherniating. The reliability of this method suggests the opportunity to investigate other anulus closure devices and nucleus replacement techniques critically.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Clinical outcomes after lumbar discectomy for sciatica: the effects of fragment type and anular competence.

BACKGROUND The surgical treatment of sciatica with discectomy is ineffective in a sizable percentage of patients, and reherniation occurs after 5% to 15% of such procedures. The purpose of the present study was to determine if competence of the disc anulus and the type of herniation could be used to predict postoperative clinical outcomes following lumbar discectomy. METHODS A prospective obs...

متن کامل

Use of Annular Closure Device (Barricaid®) for Preventing Lumbar Disc Reherniation: One-Year Results of Three Cases.

Although lumbar discectomy is an effective treatment for lumbar disc herniation, complications exist, including postoperative disc height loss, facet joint degeneration, and recurrent disc herniation. To solve these problems, annular closure devices have been utilized in other countries, producing satisfactory results, but there has been no report of annular closure device use in our country. H...

متن کامل

Performance of an Annular Closure Device in a ‘Real-World’, Heterogeneous, At-Risk, Lumbar Discectomy Population

Study design/setting Retrospective analysis of single-center registry outcomes data. Objective Assess the utility of an annular closure device (ACD) as an adjunct to limited discectomy for lumbar disc herniation (LDH). Background Recurrent lumbar disc herniation (rLDH) following limited discectomy persists at clinically significant rates, especially in large annular defect (at least 6 mm width)...

متن کامل

Hydrodynamics Analysis of Density Currents

Density Current is formed when a fluid with heavier density than the surrounding fluid flows down an inclined bed. These types of flows are common in nature and can be produced by; salinity, temperature inhomogeneities, or suspended particles of silt and clay. Driven by the density difference between inflow and clear water in reservoirs, density current plunges clear water and moves towards a d...

متن کامل

Compressive Behavior of a Glass/Epoxy Composite Laminates with Single Delamination

The buckling and postbuckling behaviors of a composite beam with single delamination are investigated. A three-dimensional finite element model using the commercial code ANSYS is employed for this purpose. The finite elements analyses have been performed using a linear buckling model based on the solution of the eigenvalues problem, and a non-linear one based on an incremental-iterative method....

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 38  شماره 

صفحات  -

تاریخ انتشار 2013