Adaptive 3D Remeshing for Metal Forming Simulation

نویسندگان

  • S. Krishnamoorthi
  • M. C. Gean
چکیده

An alternative remeshing methodology for 3D Abaqus explicit analyses which utilizes mesh mapping is presented. Excessive element distortion in 3D large deformation analyses necessitates remeshing, however in Abaqus explicit, the standard 3D remeshing techniques limits the analyst’s choice of element type. The presented technique allows remeshing of 3D perfectly plastic fully integrated higher order elements. The remeshing occurs in regions of high equivalent plastic strain or high equivalent plastic strain rate. The remeshing procedure maps the old boundary conditions, stress, and inelastic strain from the old distorted mesh. A benchmark comparing the results of an analysis using the remeshing technique to a known solution showed less than 0.2% error as a result of the remeshing procedure.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Adaptive remeshing based on a posteriori error estimation for forging simulation

This paper presents a fully automatic 3D adaptive remeshing procedure and its application to non-steady metal forming simulation. Remeshing, here, is considered as the improvement of an existing mesh rather than a complete rebuilding process. The mesh optimization technique is described. It is based on the combination of local improvement of the neighbourhood of nodes and edges. The surface and...

متن کامل

A Remeshing Procedure for Numerical Simulation

This article presents a remeshing procedure of thin sheets for numerical simulation of metal forming process in three dimensions. During simulation of metal forming processes, where large plastic deformations are possible, severe mesh distortion occur after a few incremental steps. Hence an automatic mesh generation with remeshing capabilities is essential to carry out the finite element analys...

متن کامل

شبیه‌سازی المان محدود فرایند برش متعامد و تعیین ضخامت لایه چسبنده به ابزار در ناحیه دوم برش

The built up layer thickness in secondary deformation zone is one of the important parameters in metal cutting process. The built up layer (BUL) is formed in second deformation zone near the tool-chip interface in the back of the chip. This parameter influences the tool life and machined surface quality. This BUL should not be confused with the built up edge (BUE). The deformation of the BUL in...

متن کامل

Automated Remeshing with Hexahedral Elements: Problems, Solutions, and Applications

The design process of a mesh generation tool for automatic remeshing of hexahedral element meshes is shown as well as its application to the field of simulating metal forming processes. Automatic hexahedral remeshing is very important allowing an economic analyses of processes with large deformation. Although the industry demands robust tools for automatic hexahedral remeshing, previously there...

متن کامل

All-hexahedral meshing and remeshing for multi-object manufacturing applications

All‐hexahedral meshing and remeshing algorithms giving support to finite element modeling of manufacturing processes require continuous development for improving its overall robustness and applicability. This paper draws from a previous all‐hexahedral algorithm presented by the authors and proposes new developments related to the construction of adaptive core meshes and processing of multi‐ obj...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2010