Inhaled Aerosol Distribution in Human Airways: A Scintigraphy-Guided Study in a 3D Printed Model.
نویسندگان
چکیده
BACKGROUND While it is generally accepted that inertial impaction will lead to particle loss as aerosol is being carried into the pulmonary airways, most predictive aerosol deposition models adopt the hypothesis that the inhaled particles that remain airborne will distribute according to the gas flow distribution between airways downstream. METHODS Using a 3D printed cast of human airways, we quantified particle deposition and distribution and visualized their inhaled trajectory in the human lung. The human airway cast was exposed to 6 μm monodisperse, radiolabeled aerosol particles at distinct inhaled flow rates and imaged by scintigraphy in two perpendicular planes. In addition, we also imaged the distribution of aerosol beyond the airways into the five lung lobes. The experimental aerosol deposition patterns could be mimicked by computational fluid dynamic (CFD) simulation in the same 3D airway geometry. RESULTS It was shown that for particles with a diameter of 6 μm inhaled at flows up to 60 L/min, the aerosol distribution over both lungs and the individual five lung lobes roughly followed the corresponding distributions of gas flow. While aerosol deposition was greater in the main bronchi of the left versus right lung, distribution of deposited and suspended particles toward the right lung exceeded that of the left lung. The CFD simulations also predict that for both 3 and 6 μm particles, aerosol distribution between lung units subtending from airways in generation 5 did not match gas distribution between these units and that this effect was driven by inertial impaction. CONCLUSIONS We showed combined imaging experiments and CFD simulations to systematically study aerosol deposition patterns in human airways down to generation 5, where particle deposition could be spatially linked to the airway geometry. As particles are negotiating an increasing number of airways in subsequent branching generations, CFD predicts marked deviations of aerosol distribution with respect to ventilation distribution, even in the normal human lung.
منابع مشابه
Micro Particles Transport and Deposition in Realistic Geometry of Human Upper Airways
Realistic geometry of human upper airways from mouth to the end of trachea was reconstructed by implementing the CT-Scan images of a male subject. A computational model for analyzing the airflow in the airways was developed and several simulations were performed. To capture the anisotropy of the inhaled airflow in the upper airways, the Reynolds stress transport model of turbulence was used ...
متن کاملMapping PET-measured triamcinolone acetonide (TAA) aerosol distribution into deposition by airway generation.
The three dimensional (3D) distribution of inhaled drugs was measured using Positron Emission Tomography (PET) (Berridge, M.S, Muswick, G.J., Lee, Z., Leisure, G.L., Nelson, A.D., Muzic, R.F. Jr., Miraldi, F., Heald, D.L., 1997. PET evaluation of Azmacort(R) ([C-11]triamcinolone acetonide) dose administration. J. Nucl. Med. 38 (5) Suppl., 4-5). Data analysis was based upon regional ratios or pe...
متن کاملSociety of Nuclear Medicine Procedure Guideline for Lung Scintigraphy
A. Aerosol Ventilation Scintigraphy A diagnostic imaging test that records the bronchopulmonary distribution of an inhaled radioactive aerosol within the lungs. B. Gas Ventilation Scintigraphy A diagnostic imaging test that records the pulmonary distribution of a radioactive gas during breathing maneuvers. C. Pulmonary Perfusion Scintigraphy A diagnostic imaging test that records the distributi...
متن کاملUse of a 3D printer to create a bolus for patients undergoing tele-radiotherapy
Background: This study describes the possibility of implementing three-dimensional printing technology to create a precise construction of a planned bolus, based on computed tomography information stored in the Digital Imaging and Communications in Medicine (DICOM) format file. Materials and Methods: To create the bolus with a 3D printer, we converted data in the DICOM format to the s...
متن کاملA Review of the Recent Advances and Application of 3D Printing in Pharmacy and Drug Delivery
Throughout human history, the most valuable inventions have been those that, even decades after their initial introduction, affected the lives of people around the world. 3D printers similar to steam engines, light bulbs, and the World Wide Web are thought to be among the inventions that will revolutionize the future of different industries. This technology is generally introduced as the manuf...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
- Journal of aerosol medicine and pulmonary drug delivery
دوره 29 6 شماره
صفحات -
تاریخ انتشار 2016