Using the Plastic Injection Method
نویسندگان
چکیده
The arterial vasculature in the floor region of the mouth and the submandibular region of the crab-eating monkey was studied by the acrylic plastic injection method. 1. The titled regions were found to be supplied by the hyoid branch and the sublingual artery arising from the lingual artery, and the submandibular glandular branch, the mylohyoid branch and the submental artery from the facial artery. 2. The hyoid branch supplied the mylohyoid and geniohyoid muscles. 3. The sublingual artery sent off the following branches: (1) the genioglossal branch to the genioglossus muscle, (2) the alveolingual artery to a wide area in the floor region of the mouth including several muscles, the sublingual gland and the gingiva and mucosa of the lingual side of the premolar area, (3) the sublingual papillary branch to the papilla, (4) the incisive gingival branch to the lingual gingiva of the lower incisors and canine, (5) the alveolar branch to the lower incisors, and (6) the median inferior labial artery to the lower lip and labial gingiva of the lower incisors. 4. The submandibular glandular branch of the facial artery supplied the submandibular gland. 5. The mylohyoid branch supplied the mylohyoid and digastric muscles and the lingual gingiva of the lower molars. 6. The branches of the submental artery were as follows: (1) the submandibular lymph node branch to the lymph nodes and the skin and muscles in the submandibular region, (2) the digastric branch to the digastric muscle, and (3) the gingival branch to the labial gingiva opposite the canine and lower lateral incisors.
منابع مشابه
Optimization of the injection molding process of Derlin 500 composite using ANOVA and grey relational analysis
Warpage and shrinkage control are important factors in proving the quality of thin-wall parts in injection modeling process. In the present paper, grey relational analysis was used in order to optimize these two parameters in manufacturing plastic bush of articulated garden tractor. The material used in the plastic bush is Derlin 500. The input parameters in the process were selected according ...
متن کاملA 3D Numerical and Empirical Study on the Effects of Injection Pressure and Temperature on the Quality of Produced Mold
Plastic injection is a method in which, with using an extruder in granules, plastic is injected in a hole with high pressure. Because of meeting the two flow fronts in this process welding line will be made. Along the welding line the strength of produced part is low; therefore the position of welding line and its clarity are very important. In this paper, analyzes have been done with Fluent an...
متن کاملFinding efficient frontier of process parameters for plastic injection molding
Product quality for plastic injection molding process is highly related with the settings for its process parameters. Additionally, the product quality is not simply based on a single quality index, but multiple interrelated quality indices. To find the settings for the process parameters such that the multiple quality indices can be simultaneously optimized is becoming a research issue and ...
متن کاملHypotension in Reconstructive and Plastic Surgery
to 60m.m.Hg. and with no ill effects at the end of the anaesthesia and the tremination of the operation the drops of the serum which contains 15mg. Wyamin will be increased to rise the blood pressure, now if the anaesthetic drug is Halothane recovery is quick and if Ether is used it is a little prolonged. If while operating there is need for further injection of Adrenaline solution in the ope...
متن کاملInvestigation of effective parameters on fabrication of alumina parts by low pressure injection molding (LPIM) method
Low pressure injection molding (LPIM) method in this paper is investigated as a method of forming alumina parts. This is one of the methods of making engineering ceramics with complex shapes and high dimensional accuracy. In this method, a binder system (paraffin wax + carnuba wax) was used as a plastic agent for easy formation of alumina particles. Different parameters such as feedstock temper...
متن کاملOptimization of Plastic Injection Molding Process by Combination of Artificial Neural Network and Genetic Algorithm
Injection molding is one of the most important and common plastic formation methods. Combination of modeling tools and optimization algorithms can be used in order to determine optimum process conditions for the injection molding of a special part. Because of the complication of the injection molding process and multiplicity of parameters and their interactive effects on one another, analytical...
متن کامل