Influence of Natural Aging Time on Two-Step Aging Behavior of Al-Mg-Si(-Cu) Alloys

نویسندگان

  • JaeHwang Kim
  • Equo Kobayashi
  • Tatsuo Sato
چکیده

Nanoclusters formed during natural aging cause the negative effect of the two-step aging in the age-hardenable Al-Mg-Si alloys. The relationship between the clustering behavior during natural aging and the two-step aging behavior was studied using the hardness, differential scanning calorimetry (DSC), electrical resistivity measurements, transmission electron microscopy (TEM) observation in the Cu-free and Cuadded Al-Mg-Si alloys. Three stages during the two-step aging are clearly revealed based on the hardness results. The hardness in the two-step aging with the natural aging time is decreased, increased and then decreased at the initial, middle and final stages, respectively. Si-rich clusters initially formed during natural aging do not transform into the ¢AA phase and are thermally stable during the two-step aging at 170°C. On the other hand, Mg-Si co-clusters formed at the middle stage during natural aging transform into the ¢AA phase and are thermally unstable during the twostep aging at 170°C. Much higher hardness is obtained in the Cu-added alloy than that of the Cu-free alloy during two-step aging when natural aging is performed for 3.6 ks belonging to the initial stage. The higher hardness is also found to be obtained during over-aging regardless of the natural aging time in the Cu-added alloy than that of the Cu-free alloy. The relationship between the clustering behavior during natural aging and the two-step aging behavior is discussed based on the observed age-hardening phenomena. [doi:10.2320/matertrans.L-M2015824]

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effects of Cu Addition on Behavior of Nanoclusters during Multi-Step Aging in Al-Mg-Si AlloysThe Paper Contains Partial Overlap with the ICAA12 Proceedings by USB under the Permission of the Editorial Committee

Two types of nanoclusters, i.e. Cluster (1) and Cluster (2), play a strongly important role in the bake-hardening (BH) response in Al-Mg-Si alloys. Different formation behaviors of two types of nanoclusters were studied by means of hardness, differential scanning calorimetry (DSC), electrical resistivity measurement, transmission electron microscopy (TEM) and high resolution TEM observation in ...

متن کامل

THE EFFECT OF AGING ON THE CLUSTERING AND PRECIPITATION PROCESS IN Al-Mg-Si ALLOYS

The dependence of the mechanism of age hardening in Al-Mg-Si alloys on their Si content, the pre-aging conditions and addition of Cu has been investigated. For this purpose, the solute clusters and the metastable precipitates in aged Al-Mg-Si alloys have been characterized by a three dimensional atom probe (3DAP) and transmission electron microscopy (TEM). Atom probe analysis results have revea...

متن کامل

Effect of Sn Addition on the Two-Step Aging Behavior in Al-Mg-Si Alloys for Automotive Application

Aluminum alloys of the 6xxx series which contain excess Si or Cu are well used for the automotive applications because of the high age-hardening response. The effect of addition of small amount of Sn on the two-step aging behavior in 1.2%Mg2Si-0.5%Si in excess alloy and 1.2%Mg2Si-0.7%Cu alloy was investigated by means of hardness measurement, differential scanning calorimetry, and transmission ...

متن کامل

ATOM PROBE CHARACTERIZATION OF PREPRECIPITATE CLUSTERS AND PRECIPITATES IN Al-Mg-Si(-Cu) ALLOYS

Pre-precipitation clustering and chemical nature of the metastable precipitates in aged Al-Mg-Si(-Cu) alloys have been investigated by atom probe field ion microscopy (APFIM) and transmission electron microscopy (TEM) for better understanding of the two-step aging behavior and the effect of excess Si. After a prolonged natural aging, co-clusters of Mg and Si atoms are observed in addition to se...

متن کامل

The Effect of Artificial Aging Treatment and Lubrication Modes on the Cutting Force and the Chip Surface Morphology when Drilling Al-Si-Mg (A356) Cast Alloys

This article reports the effects of various artificial aging methods and lubrication modes (dry, mist, wet) on the recorded cutting forces and chip morphology in drilling Al-Si-Mg (A356) cast alloys. In the course of this work, the work part sampled were as-received alloy (T0), solution heat-treated alloy (SHT) and then aged alloys at 155°C, 180°C, and 220°C (T4, T6, T61, T7), respectively. The...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015