Phase Relationships and Physical Properties

نویسندگان

  • Toshihiro Moriga
  • Doreen D. Edwards
  • Thomas O. Mason
  • Kenneth R. Poeppelmeier
  • Jon L. Schindler
  • Carl R. Kannewurf
  • Ichiro Nakabayashi
چکیده

Equilibrium phase relationships in the ZnO–In2O3 system were determined between 1100° and 1400°C using solidstate reaction techniques and X-ray diffractometry. In addition to ZnO and In2O3, nine homologous compounds, ZnkIn2Ok+3 (where k = 3, 4, 5, 6, 7, 9, 11, 13, and 15), were observed. Electrical conductivity and diffuse reflectance of the k = 3, 4, 5, 7 and 11 members were measured before and after annealing at 400°C for 1 h under forming gas (4% H2–96% N2). Room-temperature conductivity increased as k decreased, because of increased carrier concentration as well as increased mobility. In general, transparency in the wavelength range of 450–900 nm increased as k increased. Reduction in forming gas resulted in increased conductivity and reduced transparency for all compounds measured. The highest room-temperature conductivity measured, 270 S/cm, was that of reduced Zn3In2O6.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Modeling Investigation of Dielectric Constant Effect on NMR and IR Properties of C48 as a Single Walled Carbon Nanotube

A cluster model for active site of nanotube (C48) was presented and investigated the geometricstructure and thermochemical parameters. Quantum-mechanical calculations were performed at theHF / 510-30, 6-310, 6-3 IG• and 6-310" levels of theory in the gas phase and three solvents atfour temperatures. Also, nuclear shielding parameters of the active site of nanotube have been takeninto account us...

متن کامل

DENSIFICATION AND MICROSTRUCTURE CHARACTERISTICS OF A PREALLOYED ALPHA BRASS POWDER PROCESSED BY LIQUID PHASE SINTERING

The rapidly solidified prealloyed alpha brass powder with a size range of 40 to 100 μm produced by water atomization process was consolidated using liquid phase sintering process. The relationships between sintering temperature, physic-mechanical properties and microstructural characteristics were investigated. Maximum densification was obtained at 930 °C, under 600 MPa compacting pressure,...

متن کامل

Determination of Relationships between the Ultrasound Velocity and the Physical Properties of Bovine Cortical Bone Femur

Accurate measurements of physical characteristics of bone are essential for diagnosis, assessment of change following treatment, and therefore, indirectly, for evaluation of new forms of therapy. This is particularly true of osteoporosis and aging skeleton, in which fractures occur easily. Methods: In this study an ultrasonic system was set-up and calibrated on Plexiglas tubes of variable thick...

متن کامل

A modified variable physical properties model, for analyzing nanofluids flow and heat transfer over nonlinearly stretching sheet

In this paper, the problem of laminar nanofluid flow which results from the nonlinear stretching of a flat sheet is investigated numerically. In this paper, a modified variable physical properties model for analyzing nanofluids flow and heat transfer is introduced. In this model, the effective viscosity, density, and thermal conductivity of the solid-liquid mixture (nanofluids) which are common...

متن کامل

RELATIONSHIPS BETWEEN LIPOPHILIC CHARACTER AND BIOLOGICAL ACTIVITY OF NEW POTENTIAL LONG-ACTING LOCAL ANESTHETICS

The partition coefficients (P-values) of certain new potential, stereoselective, reversible, long-acting local anesthetics have been determined in an n-octanol/ phosphate buffer system. These are derivatives of 2-phenoxyethyldialkylamine hydrochloride, and almost all of them are readily soluble in water. Their aqueous solutions have shown different absorption maxima, and these have been use...

متن کامل

Ti-Cr-N Coatings Deposited by Physical Vapor Deposition on AISI D6 Tool Steels

In this study, physical vapor deposition (PVD) Ti-Cr-N coatings were deposited at two different temperatures 100 and 400ºC on hardened and tempered tool steel substrates. The influence of the applied deposition temperature on the physical and mechanical properties of coatings such as roughness, thickness, phase composition, hardness and Young’s modulus were evaluated. Phase compositions were st...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 1998