An investigation of the potential for laser nerve welding.

نویسندگان

  • M Korff
  • S W Bent
  • M T Havig
  • M K Schwaber
  • R H Ossoff
  • D L Zealear
چکیده

Suture repair of a severed peripheral nerve is cumbersome, presents a focus for infection and neuroma formation, and does not always produce adequate stump alignment. An alternative form of repair is laser nerve welding, which is attractive because it does not introduce foreign material into the anastomotic site, it forms a circumferential seal, and it can be performed in difficult-to-reach areas. Laser repair has not been widely accepted both because the effect of laser irradiation on intact nerves is not well documented, and the anastomotic strength of the weld has been inferior to suture repair. In the first part of the present study, rat sciatic nerves were exposed and irradiated with increasing intensities from a Sharplan CO2 and KTP laser to document nerve damage as recorded by decreases in the peak compound action potential. A new technique of laser repair (S-Q weld) was then developed that involved harvesting subcutaneous tissue from the adjacent dermis, wrapping it around the two opposed nerve stumps, and lasering it to the epineurium to effect a weld. The strength of the S-Q weld (6.1 grams) was considerably greater than that produced by laser welding alone. The third phase of the study compared regeneration at 2 months in severed rat sciatic nerves repaired by either microsuture or S-Q weld. Analysis of the compound action potential values indicated that the number of regenerating fibers after laser repair was greater than that after suture repair, although a significant difference could not be demonstrated.(ABSTRACT TRUNCATED AT 250 WORDS)

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Investigation of the ultrasonic welding strength in glass fiber reinforced thermoset polymers with surface preparation method using laser beam

In this research, tensile strength of ultrasonic welded parts made of thermoset polymer-reinforced glass fiber with surface preparation has been investiagted. In order to elevate the adhesion of two surfaces laser grooving method has been applied. Two type of thermoplastic materials including Plymethyl methacrylate (PMMA) and polypropylene (PP) have been used as interlayers. Influences of main ...

متن کامل

Experimental and Numerical Investigation of Laser Assisted PC to Polycarbonate Welding

Laser welding is a novel method for direct joining of metals and polymers, which leads to a mechanical and chemical bond between metal and polymer. In this study, feasibility of dissimilar joining between St12 and polycarbonate is studied theoretically. Then, the ND: YAG laser is implemented to join St12 and Polycarbonate. Empirical results indicate creation of a joint between St12 and polycarb...

متن کامل

Investigation of the ultrasonic welding strength in glass fiber reinforced thermoset polymers with surface preparation method using laser beam

In this research, tensile strength of ultrasonic welded parts made of thermoset polymer-reinforced glass fiber with surface preparation has been investiagted. In order to elevate the adhesion of two surfaces laser grooving method has been applied. Two type of thermoplastic materials including Plymethyl methacrylate (PMMA) and polypropylene (PP) have been used as interlayers. Influences of main ...

متن کامل

Experimental and Numerical Investigation of Laser Assisted PC to Polycarbonate Welding

Laser welding is a novel method for direct joining of metals and polymers, which leads to a mechanical and chemical bond between metal and polymer. In this study, feasibility of dissimilar joining between St12 and polycarbonate is studied theoretically. Then, the ND: YAG laser is implemented to join St12 and Polycarbonate. Empirical results indicate creation of a joint between St12 and polycarb...

متن کامل

Investigation of Microstructure weld zone of Hastelloy X Pulsed Nd-YAG laser welds

In the present study, the microstructure of welded zone of Hastelloy X sheets with thickness of 1 mm via pulsed Nd-YAG laser welding were studied. This welding process was done by autogenus and conductive method. Microstructure were observed by metallurgical OM and SEM. Results shown Solidification of the weld metal is dendritic. The dendrites in the central zone of the welding are fine and equ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Otolaryngology--head and neck surgery : official journal of American Academy of Otolaryngology-Head and Neck Surgery

دوره 106 4  شماره 

صفحات  -

تاریخ انتشار 1992