Exposure to metalworking fluid aerosols and determinants of exposure.
نویسندگان
چکیده
Metalworking fluid (MWF) aerosols are associated with respiratory disorders including asthma and hypersensitivity pneumonitis. The aims of this study were to describe exposure to inhalable MWF aerosols and volatile compounds in machine shops, to estimate the influence of important determinants of exposure and to compare different sampling techniques for MWF aerosols. Personal full-shift air samples of inhalable aerosol (PAS-6 sampler) and total aerosol (open-faced sampler) were collected on operators in five medium to big-sized machine shops in three companies. The filters were analysed gravimetrically and extracted by supercritical fluid extraction for MWF aerosol and triethanolamine content. In addition, personal measurements were taken for formaldehyde and volatile compounds on adsorbent samplers. Continuous dust measurements were performed with a real-time instrument (DataRAM) during 2 h periods, using 1-min average values. In total, 95 measurements of inhalable aerosol and extracted MWF aerosols on 51 operators were conducted. Within the companies, the average exposure to inhalable aerosol ranged from 0.19 to 0.25 mg m(-3) with geometric standard deviations from 1.56 to 1.79. On average, the extracted fraction of MWF aerosol was 67% of the inhalable aerosol concentration. The exposure levels of triethanolamine, formaldehyde and volatile compounds were generally low. About 45% of the between-worker variance could be explained by use of compressed air, lack of complete enclosure of machines or grinding as cutting task. In 21 workers with continuous aerosol measurements, short-term peak exposures during 6% of the work time contributed to approximately 25% of the average concentration of inhalable MWF aerosol. Inhalable MWF aerosol concentration measured with the PAS-6 sampler was a factor 2 higher than the concentrations derived from the open-faced sampler. These findings suggest that control measures, such as full enclosure of machines and the elimination of the use of compressed air as cleaning technique, are required to reduce the exposure to MWF aerosols to levels below the expected threshold for adverse respiratory health effects.
منابع مشابه
Reassessing The Health Risks Associated With Employee Exposure To Metalworking Fluid Microbes
Metalworking fluids provide an excellent environment for the growth and proliferation of a variety of bacteria and fungi. Historically, the incidence of infectious disease outbreaks at metalworking facilities has been rare. Consequently the primary focus of microbial contamination control efforts has been to prevent fluid biodeterioration. Research conducted over the past decade increasingly su...
متن کاملMechanisms of Metalworking Fluids Aerosols Formation
Utilization of metalworking fluids in the technological process of metalworking brings its advantages and disadvantages, mainly associated with the contamination of the working air through cutting fluid mist. The primary aim of this article is to approximate the mechanism of aerosols generation which contaminates the working air and to draw the attention to the problem of quantification of gene...
متن کاملThe Occupational Exposure Limit for Fluid Aerosol Generated in Metalworking Operations: Limitations and Recommendations
The aim of this review was to assess current knowledge related to the occupational exposure limit (OEL) for fluid aerosols including either mineral or chemical oil that are generated in metalworking operations, and to discuss whether their OEL can be appropriately used to prevent several health risks that may vary among metalworking fluid (MWF) types. The OEL (time-weighted average; 5 mg/m(3), ...
متن کاملMachine operator's lung. A hypersensitivity pneumonitis disorder associated with exposure to metalworking fluid aerosols.
Six auto parts manufacturing workers were referred for evaluation of a 6-week history of work-related dyspnea, cough, and fatigue. Two workers also reported fever and weight loss. All six worked in a machining area where a waterbased metalworking fluid was used and recirculated under high pressure, thereby creating an aerosol. Chest radiographs revealed pulmonary interstitial infiltrates in fou...
متن کاملDeterminants of exposure to metalworking fluid aerosols: a literature review and analysis of reported measurements.
An extensive literature review of published metalworking fluid (MWF) aerosol measurement data was conducted to identify the major determinants that may affect exposure to aerosol fractions (total or inhalable, thoracic and respirable) and mass median diameters (MMDs). The identification of determinants was conducted through published studies and analysis of published measurement levels. For the...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
- The Annals of occupational hygiene
دوره 52 7 شماره
صفحات -
تاریخ انتشار 2008