Thickness, strength, and plastic deformation of occlusal registration strips.

نویسندگان

  • G C Halperin
  • A R Halperin
  • B K Norling
چکیده

T he selection of an appropriate occlusal registration strip enables the dentist to work with precision and provides valuable information on occlusion. There are significant differences in the thickness, strength, and plastic deformation of the various articulating papers and occlusal registration strips. The patient’s perception of occlusal thickness ranges from 12.5 to 100 prn.“‘j The thickness of an occlusal registration strip should be below the patient’s perception. The purpose of this study was to determine the thickness, strength, and plastic deformation of selected occlusal registration strips and to list those registration strips that meet desirable standards.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Investigation of Roll Bonding between AA5083 Strips

Layered alloys and composite materials have become an increasingly popular in industrial development. The roll bonding (RB) process, as a solid phase method of bonding, has been widely used in manufacturing large layered strips. In this study, aluminum alloy (AA 5083) strips were roll bonded at warm and cold temperatures. The effects of the rolling parameters such as the amount of plastic deform...

متن کامل

Modeling and production of high strength Al strips by equal channel multi angular pressing method

Equal channel multi angular pressing (ECMAP) process is the efficient method to enhance the productivity of ultra-fine grained (UFG) materials, by increasing process continuity and as a result decreasing process required time. Comparing repetitive ECAP method, in the same period, the number of passes can be done by ECMAP. In this article, ECMAP of AL strips in two typical annealed and as receiv...

متن کامل

A new approach for fabrication of bulk MMCs using Accumulative Channel-die Compression Bonding (ACCB)

A new severe plastic deformation (SPD) based technique entitled Accumulative channel-die compression bonding (ACCB) is proposed for the fabrication of high strength multi-layered Al/Cu composites for the first time. In order to primarily demonstrate the capabilities of ACCB in the fabrication of metal matrix composites (MMCs), AA 1050 and pure Cu strips were processed. The primary Al/Cu sandwic...

متن کامل

Thickness and marking quality of different occlusal contact registration strips

OBJECTIVES Evaluate the thickness and the marking quality of different occlusal contact registration strips (OCRS) and a possible correlation between them. MATERIAL AND METHODS The following OCRS were selected: Accufilm II, BK20, BK21, BK22, BK23, BK28, and BK31. The thickness was measured in three points of the OCRS with an electronic measuring device (TESA), and the mean was calculated. To ...

متن کامل

An investigation on the bond strength of aluminum strips in presence of brass mesh after cold roll bonding

In the present study, the presence of brass mesh on the bond strength of aluminum (AA1050) strips in the cold roll bonding process was investigated. The influence of various process parameters including reduction in thickness, pre-rolling annealing, initial thickness of the strips, and post-rolling annealing was also considered. After cold roll bonding process, peeling test was carried out and ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • The Journal of prosthetic dentistry

دوره 48 5  شماره 

صفحات  -

تاریخ انتشار 1982