Design of the Prototype of Pld Auto Test Platform

نویسندگان

  • Senzu Shen
  • Hua Li
  • Zhengle Shi
  • Minghu Zhang
  • Qian Liu
چکیده

− There’re mainly two different situations for testing PLD (Programmable Logic Device) devices. One is testing of blank chips that haven’t been programmed; the other is testing of ASIC (Application Specific Integrated Circuit) devices that have been programmed. This paper presents a test method for programmed ASIC devices, including auto test and ATPG (Auto Test Pattern Generation) method for both known and unknown logics of programmed ASIC devices.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

On the Desing and Test of a Prototype of Biped Actuated by Shape Memory Alloys

In this paper the design of a biped robot actuated with Shape Memory Alloy (SMA) springs with minimum degrees of freedom is presented. SMA springs are a class of smart materials that are known for their high power to mass and volume ratios. It was shown that utilizing spring type of SMAs have many advantages as large deformation, smooth motion, silent and clean movement compared to ordinary typ...

متن کامل

A Switchgrass-based Bioethanol Supply Chain Network Design Model under Auto-Regressive Moving Average Demand

Switchgrass is known as one of the best second-generation lignocellulosic biomasses for bioethanol production. Designing efficient switchgrass-based bioethanol supply chain (SBSC) is an essential requirement for commercializing the bioethanol production from switchgrass. This paper presents a mixed integer linear programming (MILP) model to design SBSC in which bioethanol demand is under auto-r...

متن کامل

A Novel System-Level Calibration Method for Gimballed Platform IMU Using Optimal Estimation

An accurate calibration of inertial measurement unit errors is increasingly important as the inertial navigation system requirements become more stringent. Developing calibration methods that use as less as possible of IMU signals has 6-DOF gimballed IMU in space-stabilized mode is presented. It is considered as held stationary in the test location incorporating 15 di...

متن کامل

Investigating the Behavior of the Mooring System for a Conceptual Design of a Spar Floating Wind Turbine under Survival Conditions

In this paper, selecting of an appropriate mooring system for spar platform of a wind turbine consisting of chain–cable–chain is investigated based on a meta-heuristic method. The purpose is to investigate the hydrodynamic behavior of the structure and the mooring system in a normal and damaged conditions. ANSYS-AQWA software is applied to hydrodynamics analysis and the numerical results were f...

متن کامل

Design and Experimental Study of a Combined Pneumatic Plot Seed-metering Device for Cotton

This study presents a combined pneumatic seed-metering device (SMD) that could not only fill, carry, and meter seeds, but also switch quickly between seed-metering and seed-cleaning modes, and clean seeds thoroughly and rapidly. The seed-filling, seed-carrying, and seed-metering modes of the SMD were analyzed based on a theoretical kinematic model. Furthermore, a three-factor, three-level ortho...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2009