Characterization Process of MOSFET with Virtual Instrumentation for DP4T RF Switch - A Review

نویسندگان

  • Viranjay M. Srivastava
  • Kalyan S. Yadav
  • Ghanshyam Singh
چکیده

With the increasing interest in radio frequency switch by using the CMOS circuit technology for the wireless communication systems is in demand. A traditional n-MOS Single-Pole Double-Throw (SPDT) switch has good performances but only for a single operating frequency. For multiple operating frequencies, to transmitting or receiving information through the multiple antennas systems, known as MIMO system, a new RF switch is required which should be capable of operating with multiple antennas and frequencies as well as minimizing signal distortions and power consumption. We already have proposed a Double-Pole Four-Throw (DP4T) RF switch and in this research article we are discussing a process for the characterization of the MOSFET with Virtual Instrumentation. The procedure to characterize oxide and conductor layers that are grown or deposited on semiconductors is by studying the characteristics of a MOS capacitor that is formed of the conductor (Metal)-insulator-semiconductor layers for the purpose of RF CMOS as a switch is presented. For a capacitor formed of Metal-silicon dioxide-silicon layers with a thick oxide measured optically. Some of the calculated material parameters are away from the expected values. These errors might be due to several factors such as a possible offset capacitance of the probes due to improper contact with the wafer which is measured by using the LCR (Inductance-Capacitance-Resistance) meter with the help of Visual Engineering Environment Programming (VEE Pro, a Agilent product).

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Measurement Process of MOSFET Device Parameters with VEE Pro Software for DP4T RF Switch

To design a Double-Pole Four-Throw (DP4T) RF switch, measurement of device parameters is required. In this DP4T RF switch CMOS is a unit cell, so with a thin oxide layer of thickness 628 Å which is measured optically. Some of the material parameters were found by the curve drawn between Capacitance versus Voltage (C-V) and Capacitance versus Frequency (C-F) with the application of Visual Engine...

متن کامل

Performance of Double-Pole Four-Throw Double-Gate RF CMOS Switch in 45-nm Technology

In this paper, we have investigated the design parameters of RF CMOS switch, which will be used for the wireless telecommunication systems. A double-pole four-throw double-gate radio-frequency complementary-metal-oxide-semiconductor (DP4T DG RF CMOS) switch for operating at the 1 GHz is implemented with 45-nm CMOS process technology. This proposed RF switch is capable to select the data streams...

متن کامل

Capacitive Model and S-Parameters of Double-Pole Four-Throw Double-Gate RF CMOS Switch

In this paper, we have analyzed the Double-Pole Four-Throw Double-Gate Radio-Frequency Complementary Metal-Oxide-Semiconductor (DP4T DG RF CMOS) switch using S-parameters for 1 GHz to 60 GHz of frequency range. DP4T DG RF CMOS switch for operation at high frequency is also analyzed with its capacitive model. The results for the development of this proposed switch include the basics of the circu...

متن کامل

Analysis of drain Current and Switching Speed for SPDT Switch and Dpdt Switch with the Proposed DP4T RF CMOS Switch

Conventional CMOS switch uses NMOS as transistors in its main architecture requiring a control voltage of 5.0V and a large resistance at the receivers and antennas (ANTs) to detect the signal. A CMOS integrated circuit switch uses FET transistors to achieve switching between multiple paths, because of its high value of control voltage. Hence it is not suitable for modern portable devices which ...

متن کامل

A Class E Power Amplifier with Low Voltage Stress

A new output structure for class E power amplifier (PA) is proposed in this paper. A series LC resonator circuit, tuned near the second harmonic of the operating frequency is added to the output circuit. This resonator causes low impedance at the second harmonic. The output circuit is designed to shape the switch voltage of the class E amplifier and lower the voltage stress of the transistor. T...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Wireless Sensor Network

دوره 3  شماره 

صفحات  -

تاریخ انتشار 2011