Effect of warm air-drying on dentin bond strength of single-step self-etch adhesives.
نویسندگان
چکیده
The effect of warm air-drying on the dentin bond strengths of the single-step self-etch adhesives was determined. The adhesives were applied to bovine dentin followed by drying in a stream of warm air for 5, 10, and 15 s at 37°C. Resin composites were condensed into a mold and polymerized. Specimens were stored in distilled water at 37°C for 24 h, then shear tested. The surface free-energies were determined by measuring the contact angles of three test liquids placed on the cured adhesives. The dentin bond strengths varied according to the air-drying time. The value of the acid component increased slightly when drying was performed with a stream of warm air, whereas that of the base component decreased significantly. These data suggested that warm air-drying was essential to obtain adequate bond strengths, although increasing the drying time did not significantly influence the bond strength.
منابع مشابه
Comparison of the Dentin Bond Strength of Two Self-Etch Adhesives After Prolonged Air-Drying and Additional Light-Curing
Objectives It has been reported that the water, solvents, or the primer incorporated into adhesive resins decrease the polymerization, compromise the mechanical properties, reduce the bond strength, and lead to a poor bonding performance of self-etch adhesives. This article evaluated the effect of air-drying and light-curing duration of self-etch adhesives on the micro-shear bond strength betwe...
متن کاملEffect of Dentin Wetness on the Bond Strength of Universal Adhesives
The effects of dentin wetness on the bond strength and adhesive interface morphology of universal adhesives have been investigated using micro-tensile bond strength (μTBS) testing and confocal laser scanning microscopy (CLSM). Seventy-two human third molars were wet ground to expose flat dentin surfaces. They were divided into three groups according to the air-drying time of the dentin surfaces...
متن کاملاستحکام باند برشی سه نوع سیستم ادهزیو به مینا و عاج دندانهای دایمی
Background and Aims: The purpose of this experimental study was to investigate the shear bond strength of three new adhesive systems to enamel and dentin of permanent human teeth using three new etch and rinse and self-etch adhesive systems.Materials and Methods: Sixty intact caries-free third molars were selected and randomly divided into 6 groups. Flat buccal and lingual enamel and dentin sur...
متن کاملInfluence of moisture conditions on dentin bond strength of single-step self-etch adhesive systems.
This study was conducted to clarify the influence of dentin surface moisture on bond strength of single-step self-etch adhesive systems. The adhesive systems used were Adper Prompt L-Pop (AP), Clearfil tri-S Bond (CT), Fluoro Bond Shake One (FB), G-Bond (GB), and One-Up Bond F Plus (OF). Bovine mandibular incisors were wet-ground with #600 SiC to expose the labial dentin. After rinsing with tap...
متن کاملStrength and Durability of a New Adhesive Bond to Superficial Dentin Using Etch and Rinse and Self-Etch Systems: An In Vitro Study
Background and Aim: Data regarding the efficacy of universal adhesives are limited. This study aimed to assess the durability of a universal adhesive bond to superficial dentin using etch and rinse and self-etch modes. Materials and Methods: In this in vitro, experimental study, 32 sound molars were randomly divided into two groups of Scotchbond Universal adhesive with two-step etch and rins...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Dental materials journal
دوره 31 4 شماره
صفحات -
تاریخ انتشار 2012