Finite Element analysis of aluminum tube hydroforming based on non-quadratic yield function

نویسندگان

  • Farhang Pourboghrat
  • Yabo Guan
  • Frederic Barlat
چکیده

Although very accurate in representing the material anisotropy, finite element analysis based on direct use of a polycrystal model is CPU-intensive (Guan et al., 2006a). In the present study, this Taylor-type polycrystalline model was firstly used to predict the anisotropy coefficients of Yld96 yield function. Then this phenomenological anisotropic yield function was implemented into ABAQUS/Standard finite element code, using UMAT, for the hydroforming simulation of a 6061-T4 extruded aluminum tube. It was shown that compared with von Mises (1913) and Hill’s (1948) yield function, the Yld96 material model’s predictions are in better agreement with experimental data.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Investigation on the Ultrasonic Tube Hydroforming in the Bulging Process Using Finite Element Method

In ultrasonic tube hydroforming, the tube is hydro formed while the ultrasonic vibration is applied to the die. Prior studies provide experimental proof that ultrasonic tube hydroforming reduces corner radius, improves lubrication and uniform thickness. Use of ultrasonic vibration can decrease friction at the tube-die interface. Few attempts have been made to analyze the wire drawing while the ...

متن کامل

Numerical Study on Effect of Bilinear Pressure Path on Corner Filling in Hydroforming of Tube in Box-Shape Die

Die corner filling is very important in tube hydroforming process. Definition of the internal pressure path is a key factor in improving the corner filling.  However, the factors that cause improvement of corner filling are still unclear. In this paper, effect of bilinear pressure path on corner filling in hydroforming of tube in box-shape die is studied using both finite element simulation and...

متن کامل

Analytical, Experimental and Finite Element Investigation of Internal Pressure Effect in Hydroforming Process on Metallic Bellows Produced from Thin Wall Tube of Austenitic Stainless Steel Grade 316L

One of the bellows producing method is hydroforming process .Whereas some factor of hydroforming process specially internal pressure affects on final characteristics produced bellows such as bursting, wrinkling and wall thickness distribution. In this paper the effect of internal pressure factor in final quality of produced bellows will be investigated. In simulation of process, ABAQUS/Explicit...

متن کامل

Finite element comparison of single, bi-layered and three-layered tube hydroforming processes

In this paper, single, bi-layered and three-layered tube hydroforming processes were numerically simulated using the finite element method. It was found that the final bulges heights resulted from the models were in good agreement with the experimental results. Three types of modeling were kept with the same geometry, tube material and process parameters to be compared between the obtained hydr...

متن کامل

Investigating the Ultrasonic Assistance in the Tube Hydroforming Process

The purpose of introducing ultrasonic vibrations in the tube hydroforming process is to create more formability by obtaining a lower corner radius, improve thickness distribution of the wall and provide good tribological conditions at the tube and the die interface. Vibrations imposed on the die create alternating gaps which improve the formability in the tube hydroforming process in the presen...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • IJMTM

دوره 14  شماره 

صفحات  -

تاریخ انتشار 2008