The impact of involvement of biomedical scientists in specimen dissection and selection of blocks for histopathology: a study of time benefits and specimen handling quality in Ayrshire and Arran area laboratory.
نویسندگان
چکیده
AIMS To assess possible time benefits of specimen dissection by biomedical scientists (BMSs) and the quality of specimen handling by BMSs, in a department where BMSs trim those specimens requiring simple descriptions, from which standard blocks are taken. METHODS Specimen handling by BMSs and consultant pathologists was compared. Time taken for each specimen trimmed was recorded prospectively. To determine specimen handling quality, adherence to dissection standard operating procedures (SOPs) was assessed by recording retrospectively whether or not each action in the SOP had been performed. Information on subsequently required extra levels or blocks was recorded. RESULTS Analysis of data from 672 specimens trimmed by consultants showed that any given action in the SOPs was performed on average on 60.2% of applicable/assessable specimens; for 660 similar specimens trimmed by BMSs, each action was performed on average on 80.1% of specimens. Of the specimens where data on extra blocks were recorded, extra blocks were required in 3% of those trimmed by pathologists and in 4% of those trimmed by BMSs. Extra levels were required in 12% of those trimmed by pathologists and in 16% of those trimmed by BMSs. BMS trimming saves 16 hours of consultant time each month. The difference between pathologists and BMSs in time for each specimen trimmed is negligible. CONCLUSIONS The advantages of increased adherence to trimming SOPs and saving consultant time outweigh the relatively small number of extra blocks and levels required when BMSs trim. There is no reduction in quality of dissection.
منابع مشابه
Lean six sigma process improvement in specimen receiving to improve stat chemistry turnaround times
Objective: As a consequence of stat turnaround times (TATs) chronically exceeding 60 minutes, our laboratory was facing pressure to divert limited resources toward the implementation of an emergency department satellite laboratory. Peer-reviewed literature in clinical laboratory quality assurance and improvement indicates that between 60-70% of errors occur at the pre-analytical level. Thus...
متن کاملLaboratory diagnosis of fungal infections
Selection of appropriate specimens for culture and microscopic examination is based on the results of clinical and radiographic examination and consideration of the most likely fungal pathogen that may cause such an infection. Specimens should be collected under aseptic conditions or after appropriate cleaning and decontamination of the collection site and rapidly transported to the clinical my...
متن کاملAccuracy Assessment of Ultrasonic C-scan and X-ray Radiography Methods for Impact Damage Detection in Glass Fiber Reinforced Polyester Composites
The present study introduces two quantitative parameters to compare the accuracy of ultrasonic C-scan testing and X-ray radiography methods in the damaged area detection under low-velocity impact in polymer-based composites. For this purpose, the hand lay-up technique of composite processing was employed to prepare the composite specimen. A composite specimen consisting of the glass fiber reinf...
متن کاملNumerical Determination of Delamination Onset in Laminated Symmetric DCB Specimen
In this study, a novel numerical method is proposed for determination of mode-I interlaminar fracture toughness, GIc, in multi-directional (MD) double cantilever beam (DCB) specimens using fracture properties of unidirectional DCB specimens. Two factors, β and Dc are defined to minimize the undesirable effects on strain energy release rate. β describes the difference between maximum and average...
متن کاملA laboratory study on mix design to properly resemble a jointed brittle rock
In this paper attempts have been done to create a mortar with relatively high uniaxial compressive strength (UCS), easy casting, high flexibility, instant hardening, low cost and easy availability. The main use of this material is to physically model the mechanical behavior of jointed rock-like blocks. The effect of four parameters such as joint roughness coefficient (JRC), bridge length (L), b...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of clinical pathology
دوره 57 1 شماره
صفحات -
تاریخ انتشار 2004