A pendulum test as a tool to evaluate viscous friction parameters in the equine fetlock joint.

نویسندگان

  • Prisca Noble
  • Geoffroy Lumay
  • Marc Coninx
  • Bernard Collin
  • Adrien Magnée
  • Jacqueline Lecomte-Beckers
  • Jean M Denoix
  • Didier Serteyn
چکیده

An equine fetlock joint pendulum test was studied and the influence of post mortem time and intra-articular lipid solvent on the viscous frictional response examined. Fresh equine digits (group 1, n=6 controls; group 2, n=6 lipid solvent) were mounted on a pendulum tribometer. Assuming that pendular joint damping could be modelled by a harmonic oscillator fluid damping (HOFD), damping time (τ), viscous damping coefficient (c) and friction coefficient (μ) were monitored for 5h under experimental conditions (400N; 20°C). In all experiments, pendular joint damping was found to follow an exponential decay function (R(2)=0.99714), which confirmed that joint damping was fluid. The evolution of τ, c and μ was found to be significantly (P<0.05) different in the two groups, with a decrease in τ and an increase in c and μ that was faster and more prominent in digits from group 2. It was concluded that pendular joint damping could be modelled by a HOFD model. The influence of post mortem time on results suggested that, ideally, joint mechanical properties should only be tested on fresh cadavers at the same post mortem time. Moreover, the addition of lipid solvent was found to be responsible for upper viscous friction parameters and for a reduced damping time, which suggested that articular lubricating ability was compromised. This equine pendulum test could be used to test the efficacy of various bio-lubricant treatments.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

14-3-3  Protein is Detectable in Blood Serum and Fetlock Joint Synovial Fluid of High Performance Horses

Objective: To investigate whether 14-3-3 eta protein is detectable in synovial fluid and blood serum of high performance horses and to study whether any significant correlation between this and matrix metalloproteinase 1 and 3 in horse synovial fluid. Design: Clinical study. Animals: Eleven standard breed horses (seven high performances and four controls). Procedures: Blood serum and fetlock...

متن کامل

Effect of Tool Pin Threat on the Material Flow and Mechanical Properties Friction Stir Welding of 6061 Aluminum Alloy to Copper

Dissimilar joint with good quality and mechanical properties is one of the major problems the industries. One of the most commonly used methods to solve this problem is friction stir welding process. In this paper two different tool pin with simple cylindrical and screwed profile were used to finding optimization of friction stir welding parameters to reach best mixing flow, composite structure...

متن کامل

Effect of Tool Pin Threat on the Material Flow and Mechanical Properties Friction Stir Welding of 6061 Aluminum Alloy to Copper

Dissimilar joint with good quality and mechanical properties is one of the major problems the industries. One of the most commonly used methods to solve this problem is friction stir welding process. In this paper two different tool pin with simple cylindrical and screwed profile were used to finding optimization of friction stir welding parameters to reach best mixing flow, composite structure...

متن کامل

Intra-articular ketamine administration in equine midcarpal joint: clinical, biochemical and cytological evaluations

Providing suitable analgesia following diagnostic and therapeutic arthroscopic surgeries, that areconsidered to cause some degree of postoperative pain, is a necessity in equine practice. The aim of thepresent study was to evaluate the equine synovial fluid biochemical and cytological changes as well asclinical assessments of the joint following intra-articular administration of ketamine. Six a...

متن کامل

Effect of friction stir welding parameters on the ultimate tensile strength of Al-Cu tailor welded blanks

In the present study, parameters of tool rotation speed, tool travel speed and tool offsetting with different levels were used in the friction stir welding (FSW) of aluminum-copper tailor welded blanks (TWBs). The FSW of pure copper to 5052 aluminum alloy were carried out by varying tool rotation speed from 800 rpm to 1200 rpm, tool travel speed from 40 mm/min to 80 mm/min and tool offsetting f...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Veterinary journal

دوره 188 2  شماره 

صفحات  -

تاریخ انتشار 2011