The remaining dentin thickness investigation of the attempt to remove broken instrument from mesiobuccal canals of maxillary first molars with virtual simulation technique
نویسندگان
چکیده
BACKGROUND To investigate differences in the estimated minimum remaining dentin thickness (RDT) between periapical radiographs using the paralleling and parallax technique, after simulated removal of broken instrument from the mesiobuccal (MB) canal of maxillary first molar in virtual simulation model. The 3D measurement was taken as the standard for comparison. METHODS Thirty-six maxillary first molars were scanned by micro-CT and reconstructed as 3-dimensional (3D) model. A virtual fragment of an instrument was created within the MB canal in software. Removal of the broken instrument was simulated in both the 3D and 2D dataset. Then, the models of all specimens were submitted to 2D and 3D measurements for the lowest (RDT) value in each. Differences in the values between the paralleling and parallax radiographic technique and the 3D-RDT value were analyzed with two-way Analysis of Variance. The Intra-class Correlation Coefficient (ICC) was used to assess consistency of the RDT measurements between the two periapical radiographic and techniques and 3D analysis. RESULTS There was significant difference between RDT value obtained from the paralleling technique and 3D-RDT. There were no differences between RDT obtained from parallax (angled) technique and 3D-RDT. The ICC of RDT values between paralleling technique and 3D measurement were lower than 0.75. ICC between angled radiographs and 3D technique was close to 0.75. The optimal horizontal angle for the parallax technique was about 21°. CONCLUSIONS The virtual simulation technique can provide valuable insight into the benefit/risk analysis before removal of a broken instrument. Parallel radiographs overestimate the actual remain dentin thickness in mesiobuccal canals of maxillary first molars, whereas the parallel technique would give a closer estimate to the actual thickness at a projection angle of about 21°.
منابع مشابه
Comparison of the Effect of ProTaper and Gates-Glidden Drills On the Remaining Root Dentin Thickness at the Coronal Region of the Root
Background and Aim: The purpose of this study was to evaluate residual dentin thickness of the root and the area of the canal lumen in the coronal region of the mesiobuccal and mesiolingual canals of the lower first molars after canal preparation with the common method of using hand files and Gates Glidden drills or ProTaper rotary files, by Spiral Ct-Scan. Materials and Methods: In this exp...
متن کاملAn in vitro comparison between the apical seal of thermafil with lateral and vertical condensation techniques in mesiobuccal root of maxillary molars
the purpose of this study was to compare the apical seal mof thermafil with lateral and vertical condensation techniques in mesiobuccal root of maxillary first molars. 245 upper first molarteeth were extracted.among them 40 teeth were selected having 20-25 degrres of curve(according to schnider analysis) in apical one their of their mesiobuccal roots.these teeth were also selected so that the...
متن کاملMorphometric evaluation and planning of anticurvature filing in roots of maxillary and mandibular molars.
This study aimed to guide the planning of anticurvature filing using pre-determined anatomical points on teeth to establish directions for proper implementation of the technique. Two hundred digital periapical radiographs of human molar teeth were selected and divided into two groups (n = 100): MX (maxillary) and MD (mandibular) molars. Mesiobuccal roots were considered for the MX group and mes...
متن کاملبررسی آناتومی کانال ریشه مزیوباکال در دندانهای مولر اول دائمی ماگزیلا با استفاده از تکنیک تصویربرداری CBCT
Introduction: To conduct a successful endodontic treatment, one needs to identify, clean and completely obturate the whole root canals.One important reason of reduction in success of endodontic treatment in maxillary molars is failure in identification and treatment of second mesiobuccal canal. Therefore, the present study intended to analyze the anatomy of mesiobuccal root of first maxillary m...
متن کاملA Digital Stereomicroscopic Study of the Furcation Wall Thickness of Mesiobuccal Roots of Maxillary First and Second Molars
INTRODUCTION This study aimed to compare the thickness of the mesiobuccal furcal canal walls of first and second maxillary molars. MATERIALS AND METHODS This study was performed on total of 30 first and second extracted molar teeth (15 each). The mesiobuccal roots of each tooth were separated at the cement-enamel junction (CEJ) level and embedded in acrylic resin. The embedded roots were cut ...
متن کامل