Are room temperature and thermal neutral synonymous terms? An investigation of common therapeutic modality control variables.
نویسندگان
چکیده
CONTEXT Therapeutic modality control variables are thought to be thermal neutral, a term sometimes used interchangeably with room temperature. We question this common assumption. OBJECTIVE To determine thermal neutrality of common therapeutic modality control variables. DESIGN We performed 5 laboratory experiments, including (1) water temperature over 3 weeks in 3 different containers (glass, plastic, and polystyrene); (2) water temperature and volume of 4 beakers (2 insulated, 2 uninsulated) over 4 weeks, with 1 beaker of each type covered by polyethylene; and skin interface temperature of (3) a dry, nonheated hydrocollator pack held against the chest, (4) kitty litter applied to the knee, and (5) room-temperature ultrasound gel to the forearm. SETTING Therapeutic modalities laboratory. PATIENTS OR OTHER PARTICIPANTS College student volunteers were subjects in experiments 3, 4, and 5. MAIN OUTCOME MEASURE(S) We measured temperature and volume change. Data were evaluated using descriptive and interferential statistics. RESULTS Water temperature plateaued significantly below room temperature. Temperatures significantly increased in all but the open, insulated container. Open containers plateaued at approximately 2 degrees C below room temperature and lost significant amounts of water; closed containers plateaued at room temperature with negligible water loss. In experiments 3 through 5, skin temperatures rose significantly during hydrocollator pack, kitty litter, and ultrasound gel application. CONCLUSIONS Room-temperature water baths, dry hydrocollator packs, kitty litter, and ultrasound gel were not thermally neutral. Room temperature should not be used synonymously with thermal neutral. Care must be taken to ensure that control variables truly are controlled.
منابع مشابه
Experimental evaluation of thermal stability of PS- MWCNT nanocomposite as a real-time dosimeter
Introduction: Carbon nanotubes (CNTs) are ideal reinforcing fillers for a polymer matrix, because of their nanometer size, high aspect ratio and, more importantly, their excellent mechanical strength, and electrical and thermal conductivity. The CNTs are categorized into two groups: SWCNT and MWCNT. MWCNTs would have diameters ranging from 2 to 100 nm and lengths of up to tens ...
متن کاملInvestigation and zoning of thermal physiological stresses in Iran
Analysis and zoning of thermal physiological stresses in Iran Abstract Human health is influenced by weather variables in all circumstances, including atmospheric pressure, humidity and temperature around them. Based on climate hazard and climate changes, different parts of human life and economic and social strategies such as health, hydrological pollutants And agriculture had a profound ...
متن کاملInvestigation of the phononic and thermal properties of tungsten disulfide compound using density functional theory (Research Article)
In this paper, the phononic and thermal properties of tungsten disulfide have been studied. The aim of this study was to investigate the phonon and thermal properties such as heat capacity and enthalpy. The calculations are performed within the framework of density functional theory by pseudo-potential methood and by Quantum Espresso computational package and their exchange-correlation function...
متن کاملThermal Buckling Analysis of Functionally Graded Euler-Bernoulli Beams with Temperature-dependent Properties
Thermal buckling behavior of functionally graded Euler-Bernoulli beams in thermal conditions is investigated analytically. The beam with material and thermal properties dependent on the temperature and position is considered. Based on the transformed-section method, the functionally graded beam is considered as an equivalent homogeneous Euler-Bernoulli beam with an effective bending rigidity un...
متن کاملThe Effect of Welding Parameters on the Room and High Temperature Tribological Behavior of the Weld Overlaid Die
As an important problem in forging factories, dies are destroyed because of high wear rate, plastic deformation and thermal and mechanical fatigue at high temperatures. This paper is an investigation into the use of nickel super alloy with different welding parameters. Three weld overlaid alloys of inconel625, as wear resistance hardfacing materials on H13 tool steel, with different weld...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of athletic training
دوره 42 3 شماره
صفحات -
تاریخ انتشار 2007