Precipitation of T1 and θ′ Phase in Al-4Cu-1Li-0.25Mn During Age Hardening: Microstructural Investigation and Phase-Field Simulation

نویسندگان

  • Ines Häusler
  • Christian Schwarze
  • Muhammad Umer Bilal
  • Daniela Valencia Ramirez
  • Walid Hetaba
  • Reza Darvishi Kamachali
  • Birgit Skrotzki
چکیده

Experimental and phase field studies of age hardening response of a high purity Al-4Cu-1Li-0.25Mn-alloy (mass %) during isothermal aging are conducted. In the experiments, two hardening phases are identified: the tetragonal θ' (Al₂Cu) phase and the hexagonal T₁ (Al₂CuLi) phase. Both are plate shaped and of nm size. They are analyzed with respect to the development of their size, number density and volume fraction during aging by applying different analysis techniques in TEM in combination with quantitative microstructural analysis. 3D phase-field simulations of formation and growth of θ' phase are performed in which the full interfacial, chemical and elastic energy contributions are taken into account. 2D simulations of T₁ phase are also investigated using multi-component diffusion without elasticity. This is a first step toward a complex phase-field study of T₁ phase in the ternary alloy. The comparison between experimental and simulated data shows similar trends. The still unsaturated volume fraction indicates that the precipitates are in the growth stage and that the coarsening/ripening stage has not yet been reached.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

SOLUTION STRENGTHENING AND AGE HARDENING CAPABILITY OF Al-Mg-Mn ALLOYS WITH SMALL ADDITIONS OF Cu

Nine Al-(1-3)Mg-(0-0.4)Cu-0.15Si-0.25Mn (in wt%) alloys with potential applications in both packaging and automotive industries have been investigated. Tensile testing showed that solution strengthening is in good approximation linearly proportional to the Mg content. Mechanical testing and microstructural examinations of aged samples indicate that Mg2Si phase precipitates contribute to age har...

متن کامل

Mechanical Properties and Spring -Back Investigation in Creep Age Forming Process of 7075 Al Alloy

Creep age forming (CAF) process is a novel metal forming method with major benefits including improved mechanical properties and cost reduction for aviation industry applications. CAF happens due to creep phenomenon and stress-release during the artificial aging of heat-treatable  aluminum alloys. In this work, the creep age forming of 7075 Aluminum alloy at 120, 150 and 180 °C for 6, 24 and 48...

متن کامل

Study of the Enhanced Precipitation of an Aluminium 6061 Alloy Reinforced by SiC Particles in the Range of β\" Phase Temperature (RESEARCH NOTE)

An experimental method to follow the evolution of the precipitation phenomena in the metal-matrix composites using the thermoelectric power measurements is described. It is shown that one can follow the kinetics of the precipitation during aging. The influence of the reinforcement on the precipitation kinetics is studied in case of an aluminum 6061- SiC, composite (where SiC, represents SiC par...

متن کامل

MECHANISMS OFPRECIPITATES FORMATION IN AN Al- Cu- Li-ZrALLOYUSINGDSC TECHNIQUE AND ELECTRICALRESISTANCE MEASUREMENTS

Abstract: Guinier-Preston (GP) zone formation and precipitation behavior of T1 (Al2CuLi) phase during the ageingof an Al-Cu-Li-Zr alloy was studied by differential scanning calorimetry (DSC) technique and electrical resistancemeasurement of the samples. Results show that endothermic effects in the thermograms of the alloy between 180°Cand 240°C can be related to the enthalpy of GPzones dissolut...

متن کامل

Numerical Simulation Of Heat Affected Zone Microstructure During Laser Surface Melting

Microstructural changes during laser welding and laser surface treatment has been regarded by many researchers. Most researches have focused on studying the effect of various process parameters on the size and microstructure of the heat affected zone. But some studies show that the initial microstructure of the base metal can also affect the heat affected zone dimensions and final microstructur...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 10  شماره 

صفحات  -

تاریخ انتشار 2017