Reparation of the Damaged Forging Hammer Mallet by Hard Facing and Weld Cladding

نویسندگان

  • Srbislav Aleksandrović
  • Dragan Milosavljević
  • Rajko Čukić
  • Vencislav Grabulov
چکیده

During the long-term operation, mallets of the forging hammers are exposed to thermal fatigue due to the cyclic temperature changes and impact loads. Taking into account very high price, and a risk of buying frequently the new parts, the necessity of their reparation becomes obvious. The forging hammer mallet (Figure 1), is primarily exposed to the impact compressive loads, and partially also to a temperature gradient. It is happening due to the thermal stresses caused by unbalanced temperature field [1, 2, 3, 4, 5, 6]. Therefore it is clear that this very intensively loaded

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Different methods of forging; applications and obstacles

Forging is a manufacturing process that consists of shaping the metal using localized compression forces. The blows are delivered with a hammer (often an electric hammer) or a die. In this paper, different methods of forging (multi-directional forging, hot forging, near-beta forging, multi-axial forging, direct powder forging, warm forging and ring forging) are discussed. The main problems that...

متن کامل

Selection of the Optimal Hard Facing (hf) Technology of Damaged Forging

D. Arsić, V. Lazić, R. Nikolić, S. Aleksandrović, M. Djordjević, Faculty of Engineering Sciences, University of Kragujevac, Serbia, A. Sedmak, Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia, R. Nikolić, Research Center, University of Žilina, Žilina, Slovakia, R. Bakić, Tutin High School, Serbia In exploitation, the forging dies are exposed to heating up to very high...

متن کامل

The Effect of Welding Parameters on the Room and High Temperature Tribological Behavior of the Weld Overlaid Die

As an important problem in forging factories, dies are destroyed because of high wear rate, plastic deformation and thermal and mechanical fatigue at high temperatures. This paper is an investigation into        the use of nickel super alloy with different welding parameters. Three weld overlaid alloys of inconel625, as wear resistance hardfacing materials on H13 tool steel, with different weld...

متن کامل

Fabrication of synchronized hammer peening with pulsed laser welding and its effect on 6061 aluminum alloy weld

The non-continuous laser beam in pulsed lasers allows the mechanical peening between two consecutive beams on a still hot weld bead. At a very short time (20, 150 and 300 ms) after laser pulse application, mechanical peening was performed on the welding bead. To achieve these short times, the light sensor detects the nth laser pulse and the mechanical arm starts moving. Upon reaching the tip of...

متن کامل

A new approach to predict of mechanical properties at the interface of Aluminium/Copper explosive cladding by explosive scarf welding

Abstract: The purpose of this study is to produce scarf joint through explosive welding process (EXW). The scarf weld is a process in which the final bond interface is oblique. With applying the explosive welding technique, this joint can create a metallic bond between similar or dissimilar metals. In this study, chamfered end of aluminum and copper plates were joined explosively and named scar...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2010