Stress-Free Bonding Technology with Pyrex for Highly Integrated 3D Fluidic Microsystems

نویسندگان

  • Florian Thoma
  • Frank Goldschmidtböing
  • Keith Cobry
  • Peter Woias
چکیده

In this article, a novel Pyrex reflow bonding technology is introduced which bonds two functional units made of silicon via a Pyrex reflow bonding process. The practical application demonstrated here is a precision dosing system that uses a mechanically actuated membrane micropump which includes passive membranes for fluid metering. To enable proper functioning after full integration, a technique for device assembly must be established which does not introduce additional stress into the system, but fulfills all other requirements, like pressure tolerance and chemical stability. This is achieved with a stress-free thermal bonding principle to bond Pyrex to silicon in a five-layer stack: after alignment, the silicon-Pyrex-silicon stack is heated to 730 °C. Above the glass transition temperature of 525 °C Pyrex exhibits viscoelastic behavior. This allows the glass layer to come into close mechanical contact with the upper and lower silicon layers. The high temperature and the close contact promotes the formation of a stable and reliable Si-O-Si bond, without introducing mechanical stress into the system, and without deformation upon cooling due to thermal mismatch.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Wafer Bonding and Layer Splitting for Microsystems**

In advanced microsystems various types of devices (metal-oxide semiconductor field-effect transistors, bipolar transistors, sensors, actuators, microelectromechanical systems, lasers) may be on the same chip, some of which are 3D structures in nature. Therefore, not only materials combinations (integrated materials) are required for optimal device performance of each type but also process techn...

متن کامل

Fabrication of miniaturized fluidic devices using SU-8 based lithography and low temperature wafer bonding

In this paper, we present a technology for the batch-fabrication of fluidic devices which combines polymer and metal layers. The structures are fabricated by means of two-layer lithography and SU-8-based wafer bonding technique. The combination of SU-8 and metal layers allows the fabrication of “2(1/2)”-dimensional fluidic structures. We realized different types of micromixers for the investiga...

متن کامل

3D Integration Using Adhesive, Metal, and Metal/Adhesive as Wafer Bonding Interfaces

Three-dimensional (3D) integration is an emerging technology that vertically stacks and interconnects multiple materials, technologies and functional components to form highly integrated micro/nano-systems. This paper reviews the materials and technologies for three wafer bonding approaches to 3D integration using adhesive, metal, and metal/adhesive as the bonding interfaces. Similarities and d...

متن کامل

Implementation of silicon-on-glass MEMS devices with embedded through-wafer silicon vias using the glass reflow process for wafer-level packaging and 3D chip integration

This study presents a novel system architecture to implement silicon-on-glass (SOG) MEMS devices on Si–glass compound substrate with embedded silicon vias. Thus, the 3D integration of MEMS devices can be accomplished by means of through-wafer silicon vias. The silicon vias connecting to the pads of devices are embedded inside the Pyrex glass. Parasitic capacitance for both vias and microstructu...

متن کامل

Co-design of 3d Cpus with Micro-fluidic Cooling

Title of dissertation: ARCHITECTURAL-PHYSICAL CO-DESIGN OF 3D CPUS WITH MICRO-FLUIDIC COOLING Caleb Serafy, Doctor of Philosophy, 2016 Dissertation directed by: Professor Ankur Srivastava Department of Electrical Engineering The performance, energy efficiency and cost improvements due to traditional technology scaling have begun to slow down and present diminishing returns. Underlying reasons f...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:
  • Micromachines

دوره 5  شماره 

صفحات  -

تاریخ انتشار 2014