Enhanced densification of zinc powders through thermal cycling

نویسندگان

  • C. A. Schuh
  • D. C. Dunand
چکیده

The densification of zinc powders by uniaxial hot pressing is investigated under both isothermal and thermal cycling conditions. Thermal cycling results in enhanced densification kinetics as compared to isothermal compaction at the upper cycle temperature. Using mechanistic models of initial-stage powder densification, the experimental data are analyzed to reveal the creep stress-exponent and activation energy of the dominant densification mechanism. Consequently, the observed densification enhancement during thermal cycling is confirmed to be due to internal stress plasticity, which is produced by internal mismatch stresses between adjacent zinc grains with anisotropic thermal expansion.  2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Enhanced Densification of Cavitated Dispersion- Strengthened Aluminum by Thermal Cycling

We report experimental data of creep cavity shrinkage for dispersion-strengthened-cast aluminum with about 23 vol pct submicron Al2O3 dispersoids, annealed isothermally or subjected to thermal cycling without applied stress. Thermal cycling is found to increase the rate of densification by a factor of 3 to 5.5 relative to isothermal annealing at the upper cycling temperature, allowing for recov...

متن کامل

Analysis of the Influence of Starting Materials and Processing Conditions on the Properties of W/Cu Alloys

In this work, a study of the influence of the starting materials and the processing time used to develop W/Cu alloys is carried out. Regarding powder metallurgy as a promising fabrication route, the difficulties in producing W/Cu alloys motivated us to investigate the influential factors on the final properties of the most industrially demanding alloys: 85-W/15-Cu, 80-W/20-Cu, and 75-W/25-Cu al...

متن کامل

A methodology to investigate the intrinsic effect of the pulsed electric current during the spark plasma sintering of electrically conductive powders.

A novel methodology is proposed for investigating the effect of the pulsed electric current during the spark plasma sintering (SPS) of electrically conductive powders without potential misinterpretation of experimental results. First, ensemble configurations (geometry, size and material of the powder sample, die, plunger and spacers) are identified where the electric current is forced to flow o...

متن کامل

Liquid Film Capillary Mechanism for Densification of Ceramic Powders during Flash Sintering

Recently, local melting of the particle surfaces confirmed the formation of spark and plasma during spark plasma sintering, which explains the rapid densification mechanism via liquid. A model for rapid densification of flash sintered ceramics by liquid film capillary was presented, where liquid film forms by local melting at the particle contacts, due to Joule heating followed by thermal runaw...

متن کامل

The Selective Laser Sintering of Polycarbonate

This paper investigates thermal modelling of the selective laser sintering process for amorphcus polycarbonate powders. The aim is to develop a simulation for process accuracy and control which are key areas of developement for the new layer manufacturing rapid prototyping technologies. A state-of-the-art adaptive mesh 2 0 finite difference code is used simultaneously to consider heating and si...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2002