machinability improvement of 17-4ph stainless steel by cryogenic cooling

نویسندگان

salman khani

mohammad razfar

masoud farahnakyan

چکیده

17-4ph stainless steel is a martensitic precipitation hardening stainless steel that provides an outstandingcombination of high strength, good corrosion resistance, good mechanical properties, good toughness in both base metal and welds, and short time, low-temperature heat treatments that minimize warpage and scaling. this valuable alloy is widely used in the aerospace, nuclear, chemical, petrochemical, food processing, power generation, and naval industries; however, 17-4ph stainless steel is categorized as hard to machine materials due to low thermal conductivity and high toughness. tool wear in traditional machining of 17-4ph stainless steel is high; hence, low tool life causes high tooling cost. in this paper, indirect cryogenic machining was used, in order to improve machinability of 17-4ph stainless steel in turning operation with tin coated carbide insert tool. pressurized-liquid-nitrogen (ln) was used as a cryogenic coolant. nitrogen gas applied on the liquid nitrogen to pressurize it. a specific tool holder was designed and manufactured for cryogenic turning. cryogenic machining decreases temperature-dependent tool wear and increases tool life by keeping tool temperature low. cutting force, tool flank wear and maximum tool temperature have been studied as machinability parameters. cutting force was measured by the kistler 9121 piezoelectric dynamometer. the dino-lite digital microscope with 20-200x magnification was used to measure tool flank wear. the experimental results showed that cryogenically enhanced machining decreases cutting force and tool flank wear by 22 and 23 percent, respectively, compared with dry turning. predicting of tool life using linear extrapolation showed that tool life in cryogenic turning improved by 39% over dry turning. in addition, cutting force in cryogenic machining became more stable than the force in dry condition. thermal analysis of the carbide tool performed in the ansys software using experimental data. thermal analysis showed that the maximum temperature of cutting tool in cryogenic machining is 75 percent lower than dry condition.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Machinability Improvement of 17-4PH Stainless Steel by Cryogenic Cooling

17-4PH stainless steel is a martensitic precipitation hardening stainless steel that provides an outstanding combination of high strength, good corrosion resistance, good mechanical properties, good toughness in both base metal and welds, and short time, low-temperature heat treatments that minimize warpage and scaling. This valuable alloy is widely used in the aerospace, nuclear, chemical, pet...

متن کامل

Machinability Improvement of 17-4PH Stainless Steel by Cryogenic Cooling

17-4PH stainless steel is a martensitic precipitation hardening stainless steel that provides an outstanding combination of high strength, good corrosion resistance, good mechanical properties, good toughness in both base metal and welds, and short time, low-temperature heat treatments that minimize warpage and scaling. This valuable alloy is widely used in the aerospace, nuclear, chemical, pet...

متن کامل

Microstructural Study of 17-4PH Stainless Steel after Plasma-Transferred Arc Welding

The improvement of the surface qualities and surface hardening of precipitation hardened martensitic stainless steel 17-4PH was achieved by the plasma-transferred arc welding (PTAW) process deposited with Co-based alloy. The microstructure of the heat affected zone (HAZ) and base metal were characterized by optical microscope (OM), scanning electron microscope (SEM) and transmission electron mi...

متن کامل

Corrosion Fatigue of 17-4pH Stainless Steel in a Simulated Sea Water Solution

Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and corrosion fatigue tests were performed on 17-4pH specimens. Fatigue and corrosion fatigue tests were carried out at the  stress ratio of -1 an...

متن کامل

Comparison of Mechanical, Metallurgical Properties of 17-4PH Stainless Steel between Direct Metal Laser Sintering (DMLS) and Traditional Manufacturing Methods

The purpose of this research was to analyze and compare the mechanical properties of parts made using both Direct Metal Laser Sintering (DMLS) and traditional manufacturing methods like casting or forging. Previous research in DMLS was conducted using various materials, but there has been very little done for 17-4PH stainless steel. All the samples used for testing were conducted using the EOSI...

متن کامل

Investigating the microstructure and hardness of 17-4PH steel and Stellite cladded by direct laser deposition process on 17-4PH steel substrate

The purpose of this research is to laser cladding of stellite6 and stainless steel 17-4PH powders on the substrate of stainless steel 17-4PH, and investigate its solidification microstructure. The results showed that the microstructure of the stellite6 cladding has a cobalt solid solution ground phase with an FCC structure and Cr7C3 and Cr23C6 carbides. Also, the values ​​of the primary dendrit...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
journal of modern processes in manufacturing and production

ناشر: islamic azad univesity, najafabad branch

ISSN

دوره 2

شماره 3 2013

کلمات کلیدی
[ 1 7 , ' 4 p h s t a i n l e s s s t e e l ' , ' t o o l l i f e ' , ' c r y o g e n i c c o o l i n g ' , ' m a c h i n a b i l i t y ' ]

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023