gelcasting as a novel processing route to fabricate partially stabilized zirconia ceramic bodies

نویسندگان

nasim sahraei khanghah

sharif university of technology, tehran, iran mohammad ali faghihi sani

sharif university of technology, tehran, iran alireza kamali

advanced materials and technology research center, tehran, iran zahra sadeghian

research institute of petroleum industry, tehran, iran

چکیده

bioinert ceramics, like alumina and zirconia are used mainly for replacements of bones, hip joints and for dental implants. partially stabilized zirconia ceramics (psz or tzp with 3 mol.% or 5 wt.% y2o3), appear as perspective bioinert ceramics because of their high strength and corrosion resistance. in order to fabricate complex shapes, it is essential to use a near net shape processing like gelcasting as an uncomplicated method which has appropriate potential of producing special shapes with suitable green and sintered properties (like high mechanical properties and almost full density and machinability of green bodies). moreover, biocompatibility studies have proved that this processing route is nontoxic. in this experiment, micro-structural observation performed to illustrate the effect of dispersant on homogeneity of gelcast 3y-tzp bodies. it has been shown that it is possible to achieve uniform microstructure by means of appropriate amount of dispersant and ultrasonic wave. in addition, the machinability of these green bodies has been proven and some complex shaped bodies fabricated, in order to illustrate the capability of the process.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Gelcasting as a Novel Processing Route to Fabricate Partially Stabilized Zirconia Ceramic Bodies

     Bioinert ceramics, like alumina and zirconia are used mainly for replacements of bones, hip joints and for dental implants. Partially stabilized zirconia ceramics (PSZ or TZP with 3 mol.% or 5 wt.% Y2O3), appear as perspective bioinert ceramics because of their high strength and corrosion resistance. In order to fabricate complex shapes, it is essential to use a near ...

متن کامل

Stabilized zirconia as a structural ceramic: an overview.

This review introduces concepts and background from the ceramics engineering literature regarding metastable zirconia ceramics to establish a context for understanding current and emerging zirconia-based dental ceramics.

متن کامل

Ceramic Capillary Suspensions: Novel Processing Route for Macroporous Ceramic Materials

We introduce a novel method to produce macroporous ceramics by capillary suspensions. Adding a small amount (~1 vol%) of an immiscible secondary phase to a low concentration (~20 vol%) suspension can increase the yield stress by several orders of magnitude. This drastic change in flow behavior is induced by the creation of a sample-spanning particle network in the suspension controlled by capil...

متن کامل

Zirconia as a ceramic biomaterial.

Zirconia ceramics have several advantages over other ceramic materials, due to the transformation toughening mechanisms operating in their microstructure that can give to components made out of them, very interesting mechanical properties. The research on the use of zirconia ceramics as biomaterials started about twenty years ago, and now zirconia (Y-YZP) is in clinical use in THR, but developm...

متن کامل

Processing and Properties of Zirconia-Toughened Alumina Prepared by Gelcasting

Zirconia-toughened alumina (ZTA) using yttria-stabilised zirconia is a good option for ceramic-ceramic bearing couples for hip joint replacement. Gelcasting is a colloidal processing technique capable of producing complex products with a range of dimensions and materials by a relatively low-cost production process. Using gelcasting, ZTA samples were prepared, optimising the stages of fabricatio...

متن کامل

Properties of Partially Stabilized Zirconia Components Fabricated by the Ceramic On-demand Extrusion Process

The Ceramic On-Demand Extrusion (CODE) process is a novel additive manufacturing process for fabricating dense ceramic components from aqueous pastes of high solids loading. In this study, 3 mol% Y2O3 stabilized tetragonal zirconia polycrystal (3Y-TZP) parts were fabricated using the CODE process. The parts were then dried in a humidity controlled environmental chamber and sintered under atmosp...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
iranian journal of pharmaceutical sciences

جلد ۴، شماره ۱، صفحات ۷-۱۰

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023