modification of the naturally-pressurized running system for casting aluminium alloys
نویسندگان
چکیده
in this research, the effect of friction between the liquid metal and the sand mould wall and the effect of passage of liquid through a vertical bend and through a ceramic filter on the fluid flow and the melt velocity has been studied by measuring the velocity of the melt and direct observation of the liquid flow through the different parts of a naturally-pressurized running system. the friction factor was calculated using the experimental results and it was shown that the friction had a significant effect on the reduction of the melt velocity. the effect of passage of liquid through a vertical bend was measured to be 20% and a filter was estimated to reduce the liquid metal velocity by half (almost half of the effect that was stated in the literature). the design of the running system was slightly altered considering the obtained effect of filter on the melt velocity. the comparison of reliability of the castings obtained by different running systems, using a weibull statistical method, showed that the altered naturally-pressurized running system produced the most reliable castings and that the effect of the new method of running system design was greater than that of the use of a ceramic filter in the common unpressurized running system.
منابع مشابه
Continuous Roll Casting of Aluminium Alloys– Casting Parameters Analysis
The continuous roll casting process (CRC), consisting of continuous strip casting between rolls, is now well known. It was introduced by the SCAL Company (Pechiney Ugine Kuhlmann Group) 60 years ago 1 . The process consists of solidifying aluminum or aluminum alloys between the water-cooled rolls of a duo rolling mill. From the moment when solidification is completed to the moment when the stri...
متن کاملModelling of Precipitation Hardening in Casting Aluminium Alloys
Precipitation hardening, because it involves the hardening of the material over a prolonged time, is also called age hardening, or ageing. By the appropriate heat treatment of precipitation hardening, the strength or hardness of some heat-treatable aluminium alloys can be enhanced by the formation of nano-meter sized second-phase precipitated particles within the original phase matrix. The fine...
متن کاملmodification of nanoclay for improving the physico-mechanical properties of dental adhesives
هدف اصلی این مطالعه تهیه یک سامانه نوین چسب عاجی دندانی بر پایه نانورس پیوند شده با پلی متاکریلیک اسید، نانورس پیوند شده با پلی اکریلیک اسید، مخلوط نانوسیلیکا و نانورس پیوند شده با پلی متاکریلیک اسید، مخلوط نانوسیلیکا و نانورس پیوند شده با پلی اکریلیک اسید و نانورس پیوند شده با کیتوسان اصلاح شده با گلایسیدیل متاکریلات است. پیوند پلی متاکریلیک اسید و پلی اکریلیک اسید بر ری سطح نانورس در حضور و ...
Casting alloys.
Although the role of dental casting alloys has changed in recent years with the development of improved all-ceramic materials and resin-based composites, alloys will likely continue to be critical assets in the treatment of missing and severely damaged teeth. Alloy shave physical, chemical, and biologic properties that exceed other classes of materials. The selection of the appropriate dental c...
متن کاملCreep of Aluminium and Aluminium Alloys
This chapter constitutes an introduction to creep and to the creep response of Aluminium and its alloys. Its major goals are: to provide basic information on creep and its mechanisms to give a description of the more extensively used mathematical relations among creep variables (time, stress and temperature) to illustrate the creep response of pure Aluminium and of Al-Mg alloys to provide a syn...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
نشریه دانشکده فنیجلد ۴۳، شماره ۲، صفحات ۰-۰
کلمات کلیدی
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023