recovery of inconel738 superalloy from used gas turbine blades by esr method

نویسندگان

علی فرنیا

شهرام رایگان

حسین عبدی زاده

کاظم حنایی

چکیده

in this study, attempts were made to recovery the used turbine blades made up of inconel738 by electro slag remelting (esr) method. using an appropriate slag and addition of metallic aluminum, the original composition was maintained and the amount of oxygen, hydrogen and nitrogen remained in the acceptable level. in order to explore the effect of remelting with esr on the microstructure, tensile properties and age hardening behavior of the investigated alloy, the as-cast and wrought samples were solution treated at 1120 °c and aged at 845 °c for different lengths of time. the results showed that the microstructure, tensile properties and age hardening behavior of esr melted inconel738 are similar to corresponding standard values and hence, the esr method was found appropriate to be used to recovery the inconel738 alloy from the used turbine blades.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Performance Evaluation of Simple Aero Gas Turbine Cycle with Transpiration Cooling of Gas Turbine Blades

Aero gas turbine engines have been using mainly film cooling and convection cooling techniques. For operating at high gas temperature amongst different cooling options the transpiration cooling technique has emerged as the most promising technique to improve the gas turbine cycle performance by allowing higher turbine inlet temperatures. This paper investigates the advantages of transpiration c...

متن کامل

Simulation of Mist Film Cooling on Rotating Gas Turbine Blades

Film cooling technique has been successfully applied to gas turbine blades to prevent it from the hot flue gas. However, a continuous demand of increasing the turbine inlet temperature to raise the efficiency of the turbine requires continuous improvement in film cooling effectiveness. The concept of injecting mist (tiny water droplets) into the cooling fluid has been proven under laboratory co...

متن کامل

New Technologies for Modeling of Gas Turbine Cooled Blades

In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and cvazistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical subst...

متن کامل

Virtual Repair: Geometric Reconstruction for Remanufacturing Gas Turbine Blades

The usage of Direct Metal Deposition (DMD) technology for repairing defective voids in high-value metallic components is time consuming, since traditional geometric reconstruction methods are not seamlessly connected to the DMD process. Here, we consider the development of a semi-automated geometric algorithm for “virtually” repairing defective voids that appear on gas turbine airfoils after ex...

متن کامل

An Innovation in Film Cooling of the Gas Turbine Blades Applying an Upstream Jet

A new design concept is introduced to control the near-wall integration between the hot-gas boundary layer and the cooling jets in order to enhance the adiabatic film cooling effectiveness of the gas turbine blades. In this new approach, another film cooling port, having a very low blowing ratio, which prevents formation of the counter-rotating vortex pare, is applied just upstream of the main ...

متن کامل

Experimental Investigation and Analysis of Manufacturing Wind Turbine Blades Produced by Hydroforming of Aluminum Alloy AA5754

Development of new technologies and combined with creativity and innovation, plays the fundamental role in developing of any community′s value. Thus, in this research the design and production of hydroforming device was introduced. One of the best and most efficient technologies in the world of metal forming is wind turbine blade producing with hydroforming method which seems as an innovative m...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
مهندسی متالورژی و مواد

جلد ۲۳، شماره ۲، صفحات ۰-۰

کلمات کلیدی

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023