simulation and research on deep rolling process parameters
نویسندگان
چکیده
deep rolling is a kind of mechanical surface treatments that can improve surface quality, dimensional accuracy and mechanical properties of the parts. compressive residual stresses generated by the process reduce the tensile stresses during loading into the workpiece. the distribution of residual stress induced by deep rolling can be influenced by rolling parameters; such as overlap of the rolling tracks, friction coefficient between roller and target plate, deep rolling force and deep rolling mechanical tools. in the present research, the effects of these parameters are studied by finite-element simulations. the results indicate that: (i) increasing overlap results in increasing magnitude of the maximum residual stress. (ii) increases in the coefficient of friction results in decrease magnitude of the maximum residual stress and for coefficient of friction more than 0.1 the effect of friction can cause contraction. (iii) increase in the force intensity results in increase magnitude of the maximum residual stress. (iv) the deep rolling with mechanical tools and spring force provides a higher residual stress than the roller with constant force mode.
منابع مشابه
Investigation and Simulation of Wire Non-Asymmetric Rolling Process
The non-asymmetric rolling process of copper and brass wire has been simulated with the Abaqus software. Presented finite element model in this simulation of rolling predicted output curvature and contact surface width in the non-asymmetric mode (in equality of diameter of rollers, the rotational speed of the rollers and the rollers’ surface finish). The material used in this research has strai...
متن کاملNumerical and Experimental Research of Deep Drawing Process
There are mainly two methods of deep drawing analysis; experimental and analytical/numerical. Experimental analysis can be useful in analyzing the process to determine the process parameters that produce a defect free product, and the analytical/numerical modeling can be used to model and analyze the process through all stages of deformation. This approach is less time consuming and more econom...
متن کاملThe Effects of Forming Parameters on Conical Ring Rolling Process
The plastic penetration condition and biting-in condition of a radial conical ring rolling process with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, were established. The reasonable value range of mandrel feed rate in rolling process was deduced. A coupled thermomechanical 3D FE model of RCRRCDS process was established. The changing laws of equivalent plas...
متن کاملSimulation of Cold Rolling Process Using Smoothed Particle Hydrodynamics (SPH)
Regarding the reported capabilities and the simplifications of the smoothed particle hydrodynamics (SPH) method, as a mesh-free technique in numerical simulations of the deformation processes, a 2-D approach on cold rolling process was provided. Using and examining SPH on rolling process not only caused some minor developments on SPH techniques but revealed some physical realities. The chosen t...
متن کاملOptimization and Simulation of Machining Parameters in Radial-axial Ring Rolling Process
Ring rolling is a complicated process, in which rolling parameters influence directly the quality of ring. It is a process method with high productivity and few waste of material, widely used in transportation industry including automotive, shipbuilding, aerospace etc. During the rolling process of large-sized parts, crinkle and hollows often appear on surface, due to inconsistence of rolling m...
متن کاملFEM Analysis of Effect of Rolling Parameters on Cold Rolling Process
ISSN 2277 – 5056 | © 2012 Bonfring Abstract--A FEM simulation study was carried out to investigate the influence of the rolling parameters on the rolling process. Using commercial FEM software, ABAQUS, a number of cases were studied. In this paper, a twodimensional Elastic-plastic finite element model to simulate the cold rolling of thick strip with different roll angular velocity and roll diam...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
international journal of advanced design and manufacturing technologyجلد ۵، شماره ۵، صفحات ۳۱-۳۷
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023