comparison of candida albicans adherence to conventional acrylic denture base materials and injection molding acrylic materials

نویسندگان

masoomeh aslanimehr dept. of microbiology, cellular and molecular research center, qazvin university of medical sciences, qazvin, iran.

shirin rezvani habibabadi dental caries prevention research center, qazvin university of medical sciences, qazvin, iran.

ali mahmoudi dentist, private practice, shiraz, iran.

najmeh moosavi dept. of prosthodontics, school of dentistry, qazvin university of medical sciences, qazvin, iran.

چکیده

statement of the problem: candida species are believed to play an important role in initiation and progression of denture stomatitis. the type of the denture material also influences the adhesion of candida and development of stomatitis. purpose: the aim of this study was comparing the adherence of candida albicans to the conventional and injection molding acrylic denture base materials. materials and method: twenty injection molding and 20 conventional pressure pack acrylic discs (10×10×2 mm) were prepared according to their manufacturer’s instructions. immediately before the study, samples were placed in sterile water for 3 days to remove residual monomers. the samples were then sterilized using an ultraviolet light unit for 10 minutes. 1×10 8 cfu/ml suspension of candida albicans atcc-10231 was prepared from 48 h cultured organism on sabouraud dextrose agar plates incubated at 37 o c. 100 μl of this suspension was placed on the surface of each disk. after being incubated at 37 o c for 1 hour, the samples were washed with normal saline to remove non-adherent cells. attached cells were counted using the colony count method after shaking at 3000 rmp for 20 seconds. finally, each group was tested for 108 times and the data were statistically analyzed by t-test. results: quantitative analysis revealed that differences in colony count average of candida albicans adherence to conventional acrylic materials (8.3×10 3 ) comparing to injection molding acrylic resins (6×10 3 ) were statistically significant ( p <0.001). conclusion: significant reduction of candida albicans adherence to the injection acrylic resin materials makes them valuable for patients with high risk of denture stomatitis. keywords ● candida albicans   ● acrylic resins  ● denture

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Comparison of Candida Albicans Adherence to Conventional Acrylic Denture Base Materials and Injection Molding Acrylic Materials

STATEMENT OF THE PROBLEM Candida species are believed to play an important role in initiation and progression of denture stomatitis. The type of the denture material also influences the adhesion of candida and development of stomatitis. PURPOSE The aim of this study was comparing the adherence of candida albicans to the conventional and injection molding acrylic denture base materials. MATE...

متن کامل

Shear Bond Strength of Acrylic Denture Teeth to PMMA and Polyamide Denture Base Materials

Introduction: Detachment of denture teeth from denture base is one of the most common reasons for costly denture repairs .This study aimed at evaluating the bond strength of an acrylic denture tooth to polyamide injection-molded thermoplastic denture base material compared with three conventional polymethylmethacrylate (PMMA) denture base resins. Materials and Method: A total of 40 acrylic dent...

متن کامل

Factors affecting the bond strength of denture base and reline acrylic resins to base metal materials

OBJECTIVE The shear bond strengths of two hard chairside reline resin materials and an auto-polymerizing denture base resin material to cast Ti and a Co-Cr alloy treated using four conditioning methods were investigated. MATERIAL AND METHODS Disk specimens (diameter 10 mm and thickness 2.5 mm) were cast from pure Ti and Co-Cr alloy. The specimens were wet-ground to a final surface finish of 6...

متن کامل

Dimensional Changes of Acrylic Resin Denture Bases: Conventional Versus Injection-Molding Technique

OBJECTIVE Acrylic resin denture bases undergo dimensional changes during polymerization. Injection molding techniques are reported to reduce these changes and thereby improve physical properties of denture bases. The aim of this study was to compare dimensional changes of specimens processed by conventional and injection-molding techniques. MATERIALS AND METHODS SR-Ivocap Triplex Hot resin wa...

متن کامل

Hydrophilic surface modification of acrylic denture base material by silica coating and its influence on Candida albicans adherence.

Silica coating modifies hydrophobic denture base materials to have a hydrophilic surface. The purpose of this study was to evaluate the effect of silica coating to a denture base material on resistance to Candida albicans (C. albicans) adherence. Specimens were prepared by polymerizing an acrylic denture lining material and polished using silicon carbide paper up an abrasive grade of 1000. The ...

متن کامل

Comparison of Water Sorption of Two Injection Acrylic Resins with a Conventional Pressure-Packed Acrylic Resin

Background and Aim: Water sorption is one of the most important properties that affects the quality of a prosthesis, and subsequently, the quality of treatment, and pa-tient’s quality of life. The aim of this study was to determine and compare the water sorption of two types of poly methyl methacrylate (PMMA) using the injection-molding systems with a traditional acrylic resin base material. M...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
journal of dentistry, shiraz university of medical sciences

جلد ۱۸، شماره ۱، صفحات ۶۱-۰

کلمات کلیدی

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023