life cycle assessment of li-ion batteries (case study: anodes with graphite and cobalt oxide)

نویسندگان

زهرا پاداش برمچی

دانشجوی دکتری محیط زیست، دانشکدۀ منابع طبیعی، دانشگاه تهران، ایران امیرحسین حمیدیان

استادیار گروه محیط زیست، دانشکدۀ منابع طبیعی، دانشگاه تهران، ایران نعمت الله خراسانی

استاد گروه محیط زیست، دانشکدۀ منابع طبیعی، دانشگاه تهران، ایران محمود کاظم زاد

استادیار پژوهشکدۀ انرژی، پژوهشگاه مواد و انرژی، ایران

چکیده

lithium-ion batteries due to their higher energy density and lower associated environmental impacts comparing to the other batteries, recently have been highly considered. the materials used in anode, are one of the most important parts affecting batteries’ energy density and environmental impacts. the aim of this study is to investigate how environmental emissions of different materials as anode for li-ion batteries can be influenced by increasing the produced energy per mass unit of active material and also how battery recycling can change the potential environmental impacts caused by batteries. in this study, the primary weight of components needed for different scenarios was identified according to the laboratory experiences, resources and literatures. then, the primary weight data were normalized based on the identified functional unit which in this study proposed to be 1000 mah energy produced by anode active material of battery and the inventories of all the environmental impacts and energy use related to the all components used in battery including active material (synthesized anode material), electrolyte materials (lipf6 in nmp, ethylene carbonate, dimethyl carbonate) and binder were prepared using greet2 model’s data. after classification, characterization was done based on characterization factors of cml method and finally weighting of different environmental impacts was done based on met modeling method. the investigation of environmental impacts of batteries with graphite and cobalt oxide anode shows that batteries with cobalt oxide anode have higher greenhouse gas effects, acid gases, photochemical smog and energy use comparing to the batteries with graphite anode. on the other hand, the impacts of batteries with cobalt oxide anode when recycled can significantly decreased and therefore, it can be possible to achieve batteries with smaller size, lower weight and higher energy density with lower environmental impacts.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Cycle Life of Commercial Lithium-Ion Batteries with Lithium Titanium Oxide Anodes in Electric Vehicles

The lithium titanium oxide (LTO) anode is widely accepted as one of the best anodes for the future lithium ion batteries in electric vehicles (EVs), especially since its cycle life is very long. In this paper, three different commercial LTO cells from different manufacturers were studied in accelerated cycle life tests and their capacity fades were compared. The result indicates that under 55 °...

متن کامل

A generalized cycle life model of rechargeable Li-ion batteries

A generalized first principles based charge–discharge model to simulate the cycle life behavior of rechargeable Li-ion batteries has been developed. The model is based on loss of the active lithium ions due to the electrochemical parasitic reaction and rise of the anode film resistance. The effect of parameters such as depth of discharge (DOD), end of charge voltage (EOCV) and overvoltage of th...

متن کامل

Charge–discharge stability of graphite anodes for lithium-ion batteries

A graphite powder disk sandwiched between two nickel screens was used as a lithium-insertion working electrode. Electrochemical impedance spectroscopy (EIS), galvanostatic intermittent titration (GIT) using pulsed microcurrent, and in-situ intrinsic resistance measurements were used for the evaluation of kinetics and intrinsic (i.e. physical) resistance changes during charge–discharge cycling f...

متن کامل

High-rate amorphous SnO2 nanomembrane anodes for Li-ion batteries with a long cycling life.

Amorphous SnO2 nanomembranes as anodes for lithium ion batteries demonstrate a long cycling life of 1000 cycles at 1600 mA g(-1) with a high reversible capacity of 854 mA h g(-1) and high rate capability up to 40 A g(-1). The superior performance is because of the structural features of the amorphous SnO2 nanomembranes. The nanoscale thickness provides considerably reduced diffusion paths for L...

متن کامل

High-Capacity, Microporous Cu6Sn5–Sn Anodes for Li-Ion Batteries

Three-dimensional, microporous Cu6Sn5–Sn architectures were created by electrodeposition of copper and tin onto sintered copper foam substrates and evaluated as anodes for lithium-ion batteries. The electrodes were characterized before and after cycling by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectrometry. Before cycling, the electrochemically deposited f...

متن کامل

Hybrid tin oxide nanowires as stable and high capacity anodes for Li-ion batteries.

In this report, we present a simple and generic concept involving metal nanoclusters supported on metal oxide nanowires as stable and high capacity anode materials for Li-ion batteries. Specifically, SnO(2) nanowires covered with Sn nanoclusters exhibited an exceptional capacity of >800 mAhg(-1) over hundred cycles with a low capacity fading of less than 1% per cycle. Post lithiation analyses a...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
محیط زیست طبیعی

جلد ۶۸، شماره ۲، صفحات ۱۶۵-۱۷۸

کلمات کلیدی
lithium ion batteries due to their higher energy density and lower associated environmental impacts comparing to the other batteries recently have been highly considered. the materials used in anode are one of the most important parts affecting batteries’ energy density and environmental impacts. the aim of this study is to investigate how environmental emissions of different materials as anode for li ion batteries can be influenced by increasing the produced energy per mass unit of active material and also how battery recycling can change the potential environmental impacts caused by batteries. in this study the primary weight of components needed for different scenarios was identified according to the laboratory experiences resources and literatures. then the primary weight data were normalized based on the identified functional unit which in this study proposed to be 1000 mah energy produced by anode active material of battery and the inventories of all the environmental impacts and energy use related to the all components used in battery including active material (synthesized anode material) electrolyte materials (lipf6 in nmp ethylene carbonate dimethyl carbonate) and binder were prepared using greet2 model’s data. after classification characterization was done based on characterization factors of cml method and finally weighting of different environmental impacts was done based on met modeling method. the investigation of environmental impacts of batteries with graphite and cobalt oxide anode shows that batteries with cobalt oxide anode have higher greenhouse gas effects acid gases photochemical smog and energy use comparing to the batteries with graphite anode. on the other hand the impacts of batteries with cobalt oxide anode when recycled can significantly decreased and therefore it can be possible to achieve batteries with smaller size lower weight and higher energy density with lower environmental impacts.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023