Oxidation and Mechanical Behavior of Carbothermal .BETA.-SiAlON Ceramics.
نویسندگان
چکیده
منابع مشابه
Redistribution of Aluminum Ions During Processing of Sialon Ceramics
J . Phys. Chem. Solids, 41 [6] 647-52 (1979). 24E. M. Logothetis and J. K. Park, “Charge Transport and Lattice Defects in COO,” Solid State Commun., 43 [7] 543-46 (1982). ”H:C Chen and T. 0. Mason, “Thermoelectric Study of Cobaltous Oxide Defect Structure,” J . Am. Ceram. Soc., 64 [lo] C-130-C-133 (1981). 2bJ. Nowatny, 1. Sikora, and M. Rekas, “Defect Structure and Electrical Properties of Undo...
متن کاملCavitation Damage During Flexural Creep of SiAlON–YAG Ceramics
Cavitation damage in flexure bars crept at 1170°C was studied by a density measurement technique. The cavity density within the flexure beams could be approximated by a linear function of position from the tensile surface. A threshold stress for cavitation damage is suggested from the results of this study. Below the threshold tensile stress, cavitation ceases, whereas above the threshold, cavi...
متن کاملMechanical properties and failure behavior of unidirectional porous ceramics.
We show that the honeycomb out-of-plane model derived by Gibson and Ashby can be applied to describe the compressive behavior of unidirectional porous materials. Ice-templating allowed us to process samples with accurate control over pore volume, size, and morphology. These samples allowed us to evaluate the effect of this microstructural variations on the compressive strength in a porosity ran...
متن کاملEffect of Seeding on the Microstructure and Mechanical Properties of alpha-SiAlON: II, Ca-alpha-SiAlON
Seeding effects on the microstructure and mechanical properties of single-phase Ca-α-SiAlON ceramics have been investigated. Whereas a small amount of seeds can transform the microstructure from one of fine equiaxed grains to one consisting of many needle-like grains, the highest fracture toughness of 8 MPa . m1/2 is not reached until 8% seeding. This contrasts with the much higher seed efficie...
متن کاملdetermination of some physical and mechanical properties red bean
چکیده: در این تحقیق، برخی خواص فیزیکی و مکانیکی لوبیا قرمز به-صورت تابعی از محتوی رطوبت بررسی شد. نتایج نشان داد که رطوبت بر خواص فیزیکی لوبیا قرمز شامل طول، عرض، ضخامت، قطر متوسط هندسی، قطر متوسط حسابی، سطح تصویر شده، حجم، چگالی توده، تخلخل، وزن هزار دانه و زاویه ی استقرار استاتیکی در سطح احتمال 1 درصد اثر معنی داری دارد. به طوری که با افزایش رطوبت از 54/7 به 12 درصد بر پایه خشک طول، عرض، ضخام...
15 صفحه اولذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Journal of the Ceramic Society of Japan
سال: 1999
ISSN: 0914-5400,1882-1022
DOI: 10.2109/jcersj.107.786