Optimizing Microstructure and Property by Ausforming in a Medium-carbon Bainitic Steel
نویسندگان
چکیده
منابع مشابه
Microstructure Evolution during Tensile Deformation of a Nanostructured Bainitic Steel
In situ neutron diffraction experiment was used during tensile testing at room temperature to examine the changes on the percentage and texture of both ferrite and austenite in a nanocrystalline bainitic steels transformed at two different temperatures 200°C and 300oC for different times to achieve the same phase percentages. Both samples showed an inadequate capability of austenite to transfor...
متن کاملEffect of Mo Content on Microstructure and Property of Low-Carbon Bainitic Steels
In this work, three low-carbon bainitic steels, with different Mo contents, were designed to investigate the effects of Mo addition on microstructure and mechanical properties. Two-step cooling, i.e., initial accelerated cooling and subsequent slow cooling, was used to obtain the desired bainite microstructure. The results show that the product of strength and elongation first increases and the...
متن کاملThree Dimensional Optical Microstructure Analysis of Ferrite and Pearlite Phases in a Medium Carbon Steel
This work presents a three dimensional microstructural analysis of medium carbon steels, based on serial sectioning using optical microscopy. The microstructural phases considered here are ferrite and pearlite. Typically conventional 2D microscopy is used to analyze these phases, with eddy current or ultrasonic methods as alternatives. Medium carbon steel samples were heat treated in a furnace ...
متن کاملEffect of Microstructure and Notches on the Fracture Toughness of Medium Carbon Steel
Fracture toughness (K1C) of medium carbon steel (0.5% C) has been determined by round notched tensile specimen. Two notch diameters (5.6mm and 4.2mm) and three notch angles (α) namely 45, 60 and 75 have been used to observe the effect of notch diameters and notch angle on fracture toughness of the steel. By heat treatment the microstructure of the steel is also varied and its effect on the frac...
متن کاملEffects of Bainitic Transformation Temperature on Microstructure and Tensile Properties of 0.6C-Si-Mn Steel
1 緒 言 工具や軸受,ゲ ージなどの精密部品では残留オーステ ナイ ト(rR)が存在すると硬 さや疲労寿命の低下,切 削性 不良あるいは経年形状変化を招きそれらの性質に有害な 影響をもたらす.そ れゆえ,こ れ らに使用する鋼では rRを 極力減少させ るのが好 ましい.し か しなが ら,rR が低合金構造用鋼に存在する場合には延性やじん性が向 上するとともに低温におけるぜい性破壊の防止に役立つ 場合が多い.そ れゆえ,最 近進んで熱処理によって人 為的にrRの 量や存在形態を調整 し混合組織 として優れ た機械的性質 を得ようとす る研究が しばしば見受 けら れ1)~6)る.こ のようなrRを 積極的に利用 しようとする方法 として,近 年Si-Mn鋼 をベイナイ ト変態させるオース テンパー処理が注 目されている. Si-Mn鋼 をベイナイ ト変態 させた場合多量のrRが ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: ISIJ International
سال: 2020
ISSN: 0915-1559,1347-5460
DOI: 10.2355/isijinternational.isijint-2020-054