Optimization of WEDM for precise machining of novel developed Al6061-7.5% SiC squeeze-casted composite
نویسندگان
چکیده
منابع مشابه
Parametric Optimization of KERF Width and Surface Roughness in Wire Electrical Discharge Machining (WEDM) of Hybrid Aluminium (Al6061/SIC/GRAPHITE) Composite using TAGUCHI-Based Gray Relational Analysis
In this present investigation, the effect and optimization of machining parameters on the kerf width and surface roughness in wire electrical discharge machining (WEDM) operations of Al 60661 hybrid composite was studied. The hybrid metal matrix composite was fabricated by stir casting process using particulates SiC and graphite each in Al6061 alloy. The experiments were designed with L27 ortho...
متن کاملapplication and construction of carbon paste modified electrodes developed for determination of metal ions in some real samples
ساخت الکترودهاِی اصلاح شده ِیکِی از چالشهاِی همِیشگِی در دانش شیمِی بوِیژه شیمِی تجزیه مِی باشد ،که با در نظر گرفتن سادگِی ساخت، کاربردی بودن و ارزان بودن روش مِی توان به باارزش بودن چنِین سنسورهاِی پِی برد.آنچه که در ادامه آورده شده به ساخت و کاربرد الکترودهاِی اصلاح شده با استفاده از نانو ذرات در اندازه گِیرِی ولتامترِی آهن وکادمِیم اشاره دارد. کار اول اختصاص دارد به ساخت الکترود خمِیر کربن اصلاح شده با لِیگاند داِ...
15 صفحه اولAN INVESTIGATION ON CORROSION BEHAVIOUR OF A356-10 VOL.% SiC COMPOSITES IN HCl SOLUTIONS
In this study, corrosion behaviour of A356-10 vol.% SiC composites casted by gravity and squeeze casting is evaluated. For this purpose, prepared samples were immersed in HCl solution for 1h at open circuit potential. Tafel polarization and electrochemical impedance spectroscopy (EIS) were carried out to study the corrosion resistance of composites. The Tafel polarization and EIS studies of ...
متن کاملMachining Response in Turning Aluminium Composite LM13 With 15% SiC
In this paper, an attempt has been made to experimental investigation the machinability of aluminum metal matrix composite (LM13/SiC/15p) during continuous turning of composite rods using carbide inserts. Base matrix material is Aluminium LM13 reinforced with 15 % weight by volume of Silicon carbide particles of mean diameter 20 μm to 40 μm is used. The main focus of investigation is to determi...
متن کاملInfluences and Optimization of Electrical Discharge Machining Parameters for Improving form Tolerances of Micro Hole on SiC Conductive Ceramic Composite
Advanced Ceramics find wide range of industrial applications. Cutting of advanced ceramic (SiC) is very difficult using conventional machining methods due to its low fracture toughness. In the past few years, researchers have claimed successful machining of ceramic composites using EDM process. Furthermore, increasing trend, necessity of miniaturization, micro components in MEMS and semiconduct...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: The International Journal of Advanced Manufacturing Technology
سال: 2020
ISSN: 0268-3768,1433-3015
DOI: 10.1007/s00170-020-06218-5