Microwave sintering of dense and lattice 3Y-TZP samples shaped by digital light processing
نویسندگان
چکیده
Nowadays it is possible to produce ceramic parts with solid and complex shapes rapid efficient shaping sintering techniques. In this paper, 3mol% yttria stabilized zirconia (3Y-TZP) dense lattice were shaped by Digital light processing method (DLP) densified conventional (CV) microwave (MW) sintering. 3Y-TZP samples MW sintered up 1550 °C different heating rates (10, 30, 50 °C/min) for the 30 °C/min samples. Controlled thermal cycles a homogenous no runaway was reached. CV carried out at 10 °C. No inter-layer delamination detected after two methods. Both MW-sintered reached high final densities (equivalent obtained values CV-sintered samples, i.e., ≥98% T.D.), but exhibited lower average grain size than materials. The architectures between resulted in specific absorbed power: power sample that one meaning architecture heats easily.
منابع مشابه
Bonding of TRIP-Steel/Al2O3-(3Y)-TZP Composites and (3Y)-TZP Ceramic by a Spark Plasma Sintering (SPS) Apparatus
A combination of the high damage tolerance of TRIP-steel and the extremely low thermal conductivity of partially stabilized zirconia (PSZ) can provide controlled thermal-mechanical properties to sandwich-shaped composite specimens comprising these materials. Sintering the (TRIP-steel-PSZ)/PSZ sandwich in a single step is very difficult due to differences in the sintering temperature and densifi...
متن کاملSintering Behavior of 0.8 mol%-CuO-Doped 3Y-TZP Ceramics
In recent years, 3 mol% yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP) doped with copper oxide has obtained increasing interest due to its enhanced superplastisity and good potential in tribological applications. In this work, the effect of addition of small amounts (0.8 mol%) of copper oxide on the sintering behavior of 3Y-TZP was studied using a dilatometer and high-temperature X...
متن کاملDecoration of Indentation Cracks in 3y-tzp by Hydrothermal Ageing
Indentation cracks on ceramics are frequently used not only for the semi-empirical determination of the fracture toughness KIC but also as a method for generating semielliptical surface cracks to be used in as starting cracks in fracture and fatigue studies. Tetragonal zirconia stabilized with 3 % mol of yttria (3Y-TZP) is a biocompatible ceramic with good mechanical properties which is used in...
متن کاملThe Effects of Spark-Plasma Sintering (SPS) on the Microstructure and Mechanical Properties of BaTiO3/3Y-TZP Composites
Composite ceramics BaTiO₃/3Y-TZP containing 0 mol %, 3 mol %, 5 mol %, 7 mol %, and 10 mol % BaTiO₃ have been prepared by conventional sintering and spark-plasma sintering (SPS), respectively. Analysis of the XRD patterns and Raman spectra reveal that the phase composition of t-ZrO₂, m-ZrO₂, and BaTiO₃ has been obtained. Our results indicate that SPS can be effective for the decrease in grain s...
متن کاملPreparation and Optical Properties of Infrared Transparent 3Y-TZP Ceramics
In the present study, a tough tetragonal zirconia polycrystalline (Y-TZP) material was developed for use in high-speed infrared windows and domes. The influence of the preparation procedure and the microstructure on the material's optical properties was evaluated by SEM and FT-IR spectroscopy. It was revealed that a high transmittance up to 77% in the three- to five-micrometer IR region could b...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Ceramics International
سال: 2023
ISSN: ['0272-8842', '1873-3956']
DOI: https://doi.org/10.1016/j.ceramint.2022.10.194