Microstructure Characterization of WCCo-Mo Based Coatings Produced Using High Velocity Oxygen Fuel

نویسندگان
چکیده

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Possibilities of Utilization High Velocity Oxygen Fuel (hvof) Coatings in Conditions of Thermal Cyclic Loading

The item deals with the possibilities of utilization HVOF coatings in thermal cyclic loading conditions. There were evaluated three types of coatings based on WC-Co, WC-Co-Cr and Cr3C2-25NiCr. The quality of coatings was evaluated in terms of their adhesion as sprayed and also during the cyclic thermal loading, EDX analysis and evaluation of microhardness. Construction and structure of coatings...

متن کامل

Characterization of hydroxyapatiteynano-zirconia composite coatings deposited by high velocity oxy-fuel (HVOF) spray process

Hydroxyapatite (HA)ynano-zirconia composite coatings were successfully produced through high velocity oxy-fuel (HVOF) spraying of radio frequency (RF) plasma synthesized powders. Microstructure characterization and morphology analysis on the nano-structured coatings were conducted using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffractometry (XRD), and d...

متن کامل

Application of High-Velocity Oxygen-Fuel (HVOF) Spraying to the Fabrication of Yb-Silicate Environmental Barrier Coatings

From the literature, it is known that due to their glass formation tendency, it is not possible to deposit fully-crystalline silicate coatings when the conventional atmospheric plasma spraying (APS) process is employed. In APS, rapid quenching of the sprayed material on the substrate facilitates the amorphous deposit formation, which shrinks when exposed to heat and forms pores and/or cracks. T...

متن کامل

Microstructure of Laser Re-Melted AlCoCrCuFeNi High Entropy Alloy Coatings Produced by Plasma Spraying

An AlCoCrCuFeNi high-entropy alloy (HEA) coating was fabricated on a pure magnesium substrate using a two-step method, involving plasma spray processing and laser re-melting. After laser re-melting, the microporosity present in the as-sprayed coating was eliminated, and a dense surface layer was obtained. The microstructure of the laser-remelted layer exhibits an epitaxial growth of columnar de...

متن کامل

Microstructure and Wear Behavior of FeCoCrNiMo0.2 High Entropy Coatings Prepared by Air Plasma Spray and the High Velocity Oxy-Fuel Spray Processes

In the present research, the spherical FeCoCrNiMo0.2 high entropy alloy (HEA) powders with a single FCC solid solution structure were prepared by gas atomization. Subsequently, the FeCoCrNiMo0.2 coatings with a different content of oxide inclusions were prepared by air plasma spraying (APS) and high-velocity oxy-fuel spraying (HVOF), respectively. The microstructure, phase composition, mechanic...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Pamukkale University Journal of Engineering Sciences

سال: 2015

ISSN: 1300-7009,2147-5881

DOI: 10.5505/pajes.2015.56933