Investigation of heat-resistant layered coating of Al-Cr-Ni
نویسندگان
چکیده
منابع مشابه
Creep of Ni-Al and Ni-Cr-Al Superalloy Foams
The steady-state creep rate of Ni-base metallic foams, with superalloy composition (in wt. pct) Ni7.8∼9.1Al (relative density, ρ = 2.5-2.6) and Ni-13.5∼16.6Cr-5.1∼8.9Al (ρ = 2.8∼3.0), was measured under a range of temperatures (680∼825°C) and applied stresses (0.1∼0.3 MPa), and compared with that of NiAl intermetallic foams (ρ = 5.3). The stress exponent and activation energy are within the exp...
متن کاملOxidation – Nitridation of Ni-Cr-Al Alloys
A series of alloys containing 24-36 wt pct Cr and 13.5 – 25.0 wt pct Al was reacted with air at 1100 °C for 260 h. The products of isothermal reaction were scales of α-Al 2 O 3 plus small amounts of Cr 2 O 3 . These grew according to parabolic kinetics, interrupted by episodic weight losses caused by partial spallation. No nitridation occurred during the isothermal exposures. Reaction during th...
متن کاملOptimization of Composition and Heat Treatment of Age-Hardened Pt-Al-Cr-Ni Alloys
GRATZEL and R. VÖLKL, Metall. Mater. Trans., 2005, 36A, 681–689 Pt-base alloys (1) with various contents of Al, Cr and Ni were arc melted. Solution heat treatments at 1450oC followed by water quenching gave single phase alloys. Ageing at 1000oC caused the precipitation of L12 ordered particles. (1), comprising (in at.%): 11 Al; 3 Cr; 6 Ni and balance Pt, had cuboidal precipitates with edge leng...
متن کاملNanoscale Cellular Structures at Phase Boundaries of Ni-Cr-Al-Ti and Ni-Cr-Mo-Al-Ti Superalloys
The microstructural evolution of Ni-20 pct Cr wires was studied during pack cementation where Al and Ti, with and without prior cementation with Mo, are deposited to the surface of the NiCr wires and subsequently homogenized in their volumes. Mo deposition promotes the formation of Kirkendall pores and subsequent co-deposition of Al and Ti creates a triple-layered diffusional coating on the wir...
متن کاملSynthesis, structure, and mechanical properties of Ni–Al and Ni–Cr–Al superalloy foams
Reticulated nickel foams were alloyed with 8–9 wt% Al or 14–18 wt% Cr and 5–9 wt% Al in a three-step method consisting of (i) gas-phase deposition of Cr and/or Al onto the struts of a pure Ni foam by pack-cementation at 1000 C; (ii) homogenization at 1200 C to remove concentration gradients and to solutionize the alloyed struts; (iii) aging at 900 C to form c0 precipitates within the struts. Th...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: IOP Conference Series: Materials Science and Engineering
سال: 2016
ISSN: 1757-8981,1757-899X
DOI: 10.1088/1757-899x/116/1/012018