Improvements of surface tribological properties by magnetic assisted ball burnishing

نویسندگان

چکیده

The effect of the magnetic assisted ball burnishing on a general, C45 steel was investigated considering tribological aspects. In engineering practice, properties machined surfaces are characterized by amplitude roughness parameters from profiles, as Rpk, Rk, Rvk, Rsk and Rku. Information about sliding can be described these together with oil retention capacity surface. Despite conventional processes used post-machining operation, authors applied newly designed method tool, which also burnish flat or harmonically changing is able to round edge workpiece in one pass well, immediately after milling. To increase efficiency process, different types strategies were compared. results investigations showed that decreases frictional resistance, at same time it creates advantageous pockets

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

control of the optical properties of nanoparticles by laser fields

در این پایان نامه، درهمتنیدگی بین یک سیستم نقطه کوانتومی دوگانه(مولکول نقطه کوانتومی) و میدان مورد مطالعه قرار گرفته است. از آنتروپی ون نیومن به عنوان ابزاری برای بررسی درهمتنیدگی بین اتم و میدان استفاده شده و تاثیر پارامترهای مختلف، نظیر تونل زنی(که توسط تغییر ولتاژ ایجاد می شود)، شدت میدان و نسبت دو گسیل خودبخودی بر رفتار درجه درهمتنیدگی سیستم بررسی شده اشت.با تغییر هر یک از این پارامترها، در...

15 صفحه اول

Determination of Surface Roughness by Ball Burnishing Process Using Factorial Techniques

Burnishing is a method of finishing and hardening machined parts by plastic deformation of the surface. Experimental work based on central composite second order rotatable design has been carried out on a lathe machine to establish the effects of ball burnishing parameters on the surface roughness of brass material. Analysis of the results by the analysis of variance technique and the F-test sh...

متن کامل

Investigation of Sequential Cryogenic Hard Turning and Ball Burnishing Processes

K. Żak, W. Grzesik, M. Prażmowski, Opole University of Technology, Department of Manufacturing Engineering and Automation, Opole, Poland This paper presents a sequential machining process which incorporates CBN hard turning with cryogenic pre-cooling of the workpiece (CHT) and ball burnishing (BB). The main goal of this study was to select machining conditions enhancing the quality of parts mac...

متن کامل

Tribological Properties of B4C-Ni Cermet Coating Produced by HVOF Process on the Surface of 4130 Steel

In this research, B4C-Ni cermet coating was sprayed on the surface of 4130 steel from B4C and Ni feed-stockpowders using high velocity oxy-fuel (HVOF) method. In order to characterize the tribological behavior of thecoating, ball on disk wear tests were done at the ambient temperature and under the loads of 1, 3 and 5 N.Phase analysis of the coating after spraying was studied ...

متن کامل

Study of the lateral pass width for conventional and ultrasonic vibrations- assisted ball burnishing on Ti-6Al-4V specimens

Ball burnishing is a technological finishing process based on plastic deformation of the objective surface by means of a hard ball gliding over it. Along with its easiness of application, possible on the same machine where machining was performed [1], burnishing is a comprehensive process able to achieve surface roughness improvements, and compressive residual stresses up to deep layers of the ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Surface & Coatings Technology

سال: 2022

ISSN: ['1879-3347', '0257-8972']

DOI: https://doi.org/10.1016/j.surfcoat.2022.128317