Formation of Composite Coatings during Detonation Spraying of Cr3C2

نویسندگان

چکیده

In the current practice of applying carbide-based coatings by thermal spraying, starting material usually contains a metal binder. However, it is important to study possibility spraying binder-free carbides, since components reduce operating temperature and corrosion resistance cermet coatings. this work, powder chromium carbide, Cr3C2, was sprayed using CCDS2000 detonation gun. Acetylene–oxygen mixtures C2H2 + kO2 with k varying from 0.8 3.0 were used as an energetic material. Due chemical reactions between Cr3C2 products, composite nature (multi-phase materials) composition depending on k. At values in range 1.1, along contained carbonitride Cr3N0.4C1.6. 1.3 2.0, Cr7C3 Cr main As increased 3.0, Cr, CrO Cr2O3 oxides formed The mechanical properties wear found depend their phase compositions. Coatings produced may be useful for increasing machine parts mineral acids high-temperature oxidation resistance.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Plasma spraying of micro-composite thermal barrier coatings

The thermal barrier coatings (TBCs) by gas tunnel-type plasma spraying exhibited ceramic-composite features consisting of a host oxide matrix ceramic with an embedded second phase material. The densities of the composite TBC were found to be higher than those sprayed with 100wt% ZrO2 or Al2O3. In the coatings produced with powder mixtures of 50wt%, the embedded splats are found to have a relati...

متن کامل

simulation and experimental studies for prediction mineral scale formation in oil field during mixing of injection and formation water

abstract: mineral scaling in oil and gas production equipment is one of the most important problem that occurs while water injection and it has been recognized to be a major operational problem. the incompatibility between injected and formation waters may result in inorganic scale precipitation in the equipment and reservoir and then reduction of oil production rate and water injection rate. ...

Structure of Biocompatible Coatings Produced from Hydroxyapatite Nanoparticles by Detonation Spraying

Detonation-produced hydroxyapatite coatings were studied by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), Raman spectroscopy, and electron paramagnetic resonance (EPR) spectroscopy. The source material for detonation spraying was a B-type carbonated hydroxyapatite powder. The coatings consisted of tetracalcium phosphate and apatite. The ratio depended slightly on the degre...

متن کامل

In situ Particle Generation and Splat Formation During Solution Precursor Plasma Spraying of YttriaStabilized Zirconia Coatings

Thermal barrier coatings (TBCs) based on Yttria-stabilized Zirconia (YSZ) deposited by the solution precursor plasma spray (SPPS) technique have been claimed to exhibit superior durability compared to conventional plasma spraying and even electron-beam physical vapor deposition. This has been attributed to the interesting features, like vertical cracks, nanosized pores, and fine splats that are...

متن کامل

Structural characterization of laser-treated Cr3C2–NiCr coatings

The interconnected porosity of the Cr3C2–NiCr coatings obtained by high-velocity oxy fuel spraying is detrimental in corrosion and wear resistance applications. Laser treatments allow sealing of their surfaces through melting and resolidification of a thin superficial layer. A Nd:YAG laser beam was used to irradiate Cr3C2–NiCr coatings either in the continuous wave mode or at different repetiti...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Journal of composites science

سال: 2023

ISSN: ['2504-477X']

DOI: https://doi.org/10.3390/jcs7020071