Evaluation of Pure Titanium Welded Joints Produced by Underwater Friction Stir Welding

نویسندگان

چکیده

Underwater friction stir welding (UWFSW) is an advancement of conventional welding, which performed in air. The need for underwater calls more information to be explored the different materials. aim this research investigate UWFSW 2 mm titanium sheet joints their tensile and microstructural properties compare them with results (FSW) Also, nondestructive tests, such as radiography dye penetrant were carried out identify occurrence any weld defects. rotational speed FSW tool its travelling considered process parameters, while other parameters like tilt angle tool, shape pin, etc. kept constant. show that welded higher strengths achieved at a lower 140 mm/min 400 500 rpm UWFSW, respectively. mechanical yield strength, hardness are improved when compared due proper mixing metal effective cooling water environment. In FSW, YS TS values observed, 95.9% 75.1% base values, respectively, mm/min. However, elongation % much both metal. These supported by microstructure test outcomes.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Automatic seam-tracking of friction stir welded T-joints

In this research, a method for implementing automatic seam-tracking for friction stir welding, referred to hear as WeaveTrack, is presented. In this extrumum-seeking control technique, the tool weaves back and forth during welding to maintain the location where axial force is greatest, which is shown to be the center of the weld. Results demonstrate the effectiveness of this technique in tracki...

متن کامل

Friction stir welding of dissimilar joint of aluminum alloy 5083 and commercially pure titanium

In this study, commercially pure titanium and aluminum alloy 5083 in connection rotational speed of 1120 rpm and a feed rate of 50 mm per minute for butt welding by friction stir welding has been successfully completed. Micro-structure, hardness and tensile test was conducted on the connection. Welding area is a composite of aluminum and titanium particles that the particles plays an important ...

متن کامل

Friction stir welding of dissimilar joint of aluminum alloy 5083 and commercially pure titanium

In this study, commercially pure titanium and aluminum alloy 5083 in connection rotational speed of 1120 rpm and a feed rate of 50 mm per minute for butt welding by friction stir welding has been successfully completed. Micro-structure, hardness and tensile test was conducted on the connection. Welding area is a composite of aluminum and titanium particles that the particles plays an important ...

متن کامل

Seam-Tracking for Friction Stir Welded Lap Joints

This article presents a method for automatic seam-tracking in friction stir welding (FSW) of lap joints. In this method, tracking is accomplished by weaving the FSW tool back-and-forth perpendicular to the direction of travel during welding and monitoring force and torque signals. Research demonstrates the ability of this method to automatically track weld seam positions. Additionally, tensile ...

متن کامل

Investigation of the effect of temperature on the corrosion behavior of welded joints similar of titanium alloy Ti-6Al-4V by friction stir welding method

In this study, corrosion behavior of Ti-6Al-4V titanium alloy joint by friction stir welding with a rotational speed of 375 rpm and a travel speed of 100 mm/min was investigated. The welding procedure was carried out under β-transus temperature that was consisted of equiaxed grains in the stir zone. The corrosion behavior of the welded joint was investigated in 3.5% NaCl solution at temperature...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Advances in Materials Science and Engineering

سال: 2023

ISSN: ['1687-8434', '1687-8442']

DOI: https://doi.org/10.1155/2023/2092339