EROSION WEAR AND HARDNESS SHORE D OF EPOXY RESIN FILLED WITH PISTACHIO POWDER

نویسندگان

چکیده

In this research, erosion wear rate and hardness shore D for polymer biocomposite materials were investigated. The present bio-composites made up of differing weight percentage pistachio shell powder (0%, 5%, 7%, 9%) with epoxy resin was prepared by hand layout method. rates bio composites obtained under constant factors (10 hours, 60º impingement angles, sand silica particles 850μm, standoff distance 23 cm, flow 45 L/min, room temperature, nozzle diameter 4mm pump 50 mm). Results show that the specimen (epoxy + 9% powder) has best resistance compared other specimens, also reinforced have lower density highest water absorption it is found improving in (11.5%) (775%). study reveals addition to reduces its semi ductile behavior.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Thermal Conductivity of Epoxy Resin Composites Filled with Combustion Synthesized h-BN Particles.

The thermal conductivity of epoxy resin composites filled with combustion-synthesized hexagonal boron nitride (h-BN) particles was investigated. The mixing of the composite constituents was carried out by either a dry method (involving no use of solvent) for low filler loadings or a solvent method (using acetone as solvent) for higher filler loadings. It was found that surface treatment of the ...

متن کامل

Sliding Wear Behaviour of Walnut Shell Powder Filled Vinyl Ester/ WSP Green Composites

Polyvinyl ester green composites were synthesized with walnut shell powder (WSP) by in-situ polymerization technique. The green composites have been evaluated for mechanical properties such as tensile strength, tensile modulus and hardness. Sliding wear loss, specific wear rate and coefficient of friction were investigated by using computerized pin-on–disc machine at normal applied loads of 20,...

متن کامل

Erosion-corrosion and wear

The basic processes of wear, erosion and erosion-corrosion are reviewed. It is shown that oxide debris can accelerate wear when it is present as particulates, or protect and reduce friction when it is present as a glaze. Erosion-corrosion processes can be understood and organized in a series of regimes that represent a sequence of change in the relative intensities of erosive and corrosive proc...

متن کامل

Hardness of composite resin polymerized with different light-curing units

Introduction: The degree of polymerization depends on the type of light-curing unit. The aim of this study was to compare the hardness of composite resin cured by LED and Halogen light curing units. Methods: In this experimental study, 20 cylindrical samples of Tetric Ceram composite were prepared. Half of them were cured with Ultralume 2 LED and the other half with Astralis 7 Halogen light ...

متن کامل

Effect of cure cycle on curing process and hardness for epoxy resin

A 3-dimensional finite element model is developed to simulate and analyze the temperature and degree of cure field of epoxy casting part during cure process. The present model based on general finite element software ABAQUS is verified by literature example and experimental data. The numerical results show good agreement with literature example and measured data, and are even more accurate than...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Ma?alla? al-?ir?qiyya? li-l-handasa? al-m?k?n?kiyya? wa-handasa? al-maw?dd

سال: 2021

ISSN: ['1819-2076', '2313-3783']

DOI: https://doi.org/10.32852/iqjfmme.v21i1.536