Dilution Effect during Laser Cladding of Inconel 617 with Ni-Al Powders
نویسندگان
چکیده
منابع مشابه
تأثیر پارامترهای آسیاکاری مکانیکی بر تشکیل پوشش Ni-Al روی سطح سوپرآلیاژ پایه نیکل (617 Inconel)
در این تحقیق از روش آسیاکاری مکانیکی برای ایجاد پوشش Ni-Al بر سطح سوپرآلیاژ پایه نیکلی(617 Inconel) استفاده‌شده است. در این روش بمنظور تشکیل پوشش، پودر Al و زیرلایه(617 Inconel) همراه با گلولههای با قطرهای متفاوت و نسبت وزنی گلوله به پودر متفاوت درون محفظه دستگاه آسیای سیارهای قرار گرفتند و عملیات آسیاکاری در زمانهای 5 و 10 و 15 و 20 ساعت انجام شد. در حین انجام فرآیند آسیاکاری در اثر برخورد...
متن کاملLaser cladding of copper base alloys onto Al Si7 Mg0.3
Certain copper alloys have proved to be suitable for laser cladding onto aluminium base. By using the blown powder technique with a 1.5 KW C02 laser, clads without cracks or porosity have been produced. The base material has the composition Al Si7 Mg0.3 and the clads are made from alloyed copper with varying contents of Ni, Fe, Si and Al. Aluminium dilution in the clad can be kept lower than 1 ...
متن کاملThe effect of overlapping percent on microstructure and mechanical properties of laser cladding of Inconel 625 powder on ASTM A592 steel
In this study, the effect of overlapping percentage on microstructure and mechanical properties of a single-pass coating by Inconel 625 powder laser has been investigated for quench-tempered ASTM A592 steel. In order to have a structural analysis, the inter dendritic distance was evaluated. For this purpose, scanning electron microscopy (FESEM) and Digimizer software were adopted. In order to i...
متن کاملThe effect of overlapping percent on microstructure and mechanical properties of laser cladding of Inconel 625 powder on ASTM A592 steel
In this study, the effect of overlapping percentage on microstructure and mechanical properties of a single-pass coating by Inconel 625 powder laser has been investigated for quench-tempered ASTM A592 steel. In order to have a structural analysis, the inter dendritic distance was evaluated. For this purpose, scanning electron microscopy (FESEM) and Digimizer software were adopted. In order to i...
متن کاملEffect of Cobalt on Microstructure and Wear Resistance of Ni-Based Alloy Coating Fabricated by Laser Cladding
Ni-based alloy powders with different contents of cobalt (Co) have been deposited on a 42CrMo steel substrate surface using a fiber laser. The effects of Co content on the microstructure, composition, hardness, and wear properties of the claddings were studied by scanning electron microscopy (SEM), an electron probe microanalyzer (EPMA), X-ray diffraction (XRD), a hardness tester, and a wear te...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Modern Applied Science
سال: 2011
ISSN: 1913-1852,1913-1844
DOI: 10.5539/mas.v5n1p50